Ingersoll-Rand 6696X-X Septic System User Manual


 
E1996 D PRINTED IN U.S.A.
&
(419) 636–4242
D
F
AX (419) 633–1674
INGERSOLL–RAND COMPANY
ONE
ARO CENTER
D
BR
Y
AN, OHIO 43506–0151
T
OPERATOR’S
MANUAL
6696X–X
RELEASED: 2–12–91
REVISED: 11–22–96
(REV.
G)
INCLUDING:ĂSERVICE KIT, TROUBLESHOOTING, PARTS LIST, DISASSEMBLY AND REASSEMBLY
FOUR–BALL
STYLE LOWER PUMP END
ALSO COVERS 637240-X43 & 637241-C33 SERVICE KITS
66960–XXX
(CARBON STEEL)
66963–XXX
(CARBON STEEL)
66961–XXX
(400 ST
AINLESS STEEL)
(CANCELLED 9/96)
(Replaced by66963-XXX)
(ELECTROLESS NICKEL PLATED)
READ THIS MANUAL CAREFULL
Y BEFORE INST
ALLING,
OPERA
TING OR SER
VICING THIS EQUIPMENT
.
LOWER PUMP END OPTION DESCRIPTION CHART*
āX
PACKING MATERIAL
PLUNGER TYPE
SPRINGARRANGEMENT
PACKING MATERIAL (PACKINGS AREUPPER AND LOWER UNLESS NOTED)
1 J THIOKOL LEATHER C UHMW-PE
7 GLASS FILLED TEFLON (UPPER) F UHMW-PE/ LEATHER STAG'D (UPPER)
VIRGIN TEFLON (LOWER
) UHMW-PE (LOWER)
8 J TEFLON (GF) / LEATHER STAG'D (UPPER) P UHMW-PE / TEFLON STAG'D (UPPER)
VIRGIN TEFLON (LOWER) UHMW-PE (LOWER)
A J UHMW-PE(UPPER) R TEFLON / UHMW-PE STAG'D (UPPER)
LEATHER (LOWER) TEFLON (LOWER)
B J UHMW-PE(UPPER)
TEFLON (LOWER)
SPRING ARRANGEMENT
1 COIL SPRING J
2 COMPOSITE SPRING J
3 NO SPRING J
4 MULTIPLE WAVE SPRING
PLUNGER TYPE
3 HD SS W/HD CHROME PLATING
436696
PUMP MATERIAL
0 CARBON STEEL (CAN'D 9/96)
1 400 STAINLESS STEEL
3 CARBON STEEL - E NICKEL PLATED
* NOT ALL MODEL COMBINATIONS ARE AVAILABLE, REFER TO PUMP MODEL MANUAL (650XXX-XXX) FOR ``ACTIVE" MODELS.
J AS OF MAY 15, 1995 NO LONGER AVAILABLE
āX
PUMP MATERIAL
SERVICE KITS
Use only genuine ARO replacement parts to assure compatible
pressure rating and longest service life.
637240-X43 & 637241-C33 for general repair of 6696X-X43 LowĆ
er Pump Ends.
GENERAL
DESCRIPTION
LOWER PUMP END
WARNING
DO NOT EXCEED MAXIMUM OPERATING PRESĆ
SURE AS INDICATED ON PUMP MODEL PLATE.
WARNING
REFER TO GENERAL INFORMATION SHEET
FOR ADDITIONAL SAFETY PRECAUTlONS AND IMPORTANT
INFORMATION. (See the pump model manual for the proper Form
No.)
This is one of the four documents which support the pump.
Replacement copies of these forms are available upon request.
- 650XXX-āX-X MODEL OPERATOR'S MANUAL
- GENERAL INFORMATION - INDUSTRIAL PISTON PUMPS
= 6696Xā-āX LOWER PUMP END OPERATOR'S MANUAL
- AIR MOTOR OPERATOR'S MANUAL
The four-ball design provides for easy priming of the lower foot
valve. The double acting feature is standard on all ARO industrial
pumps. Material is delivered to the pump discharge outlet on both
the up and down stroke.
TROUBLE
S
HOOTING FOUR–BALL PUMPS
Lower Pump End Problems
No material at outlet / pump continually cycles.
Check material supply, disconnect or shut off the air supply and reĆ
plenish the material, reconnect.
Material on one stroke only / fast downstroke.
The lower balls may not be seating in the foot valve (see lower
pump disassembly). Remove the balls from the foot valve, clean
and inspect the ball and valve seat area. If balls or foot valve are
damaged, replace.
Material on one stroke only / fast upstroke.
Check for worn or damaged seals. Replace the seals as necessary.
Material leakage out of the solvent cup or material appears on the
pump plunger rod.
For Models (-X4X Only). Increase the load on thepackings by tightĆ
ening the packing nut. Check for worn upper packings and replace
them as necessary.