Hunter Fan 37407 Humidifier User Manual


 
©2008 Hunter Fan Co. 43002 Rev 04-29
4
When the Water Tank is empty, the humidifier will automatically
turn off and the red Refill Tank LED will turn on. The Refill Tank
LED will turn off when the Tank is refilled and placed back on
the humidifier.
current Fan speed setting. Press the Speed button until the
LED Display shows your desired Fan speed setting, Low (1),
Medium (2), or High (3). Release the Speed button. After 2
seconds, the Fan speed is set and the LED Display will show
the relative humidity.
10. During normal operation, the LED Display will show the
relative humidity of the space in which you place your
humidifier.
Features and Options
Automatic Shut-Off
Timer
You can set your humidifier to run for pre-set periods of time.
1. To see the current Timer setting, press the Timer button
once.
2. To change the Timer setting, press the Timer button and
hold it for 3 seconds. The current Timer setting will begin to
flash.
3. Press the Timer button again to change the setting. The
settings in hours are OF (Off), 2, 4, 8 and 10.
4. When the LED Display shows your desired run time, release
the Timer Button. After 2 seconds, the run time is set and the
LED Display will show the relative humidity.
5. The humidifier will shut down automatically when the set time
expires.
Span Setting
Your humidier is set at the factory to cycle at setting 2. If
you nd your humidier is cycling either too often of not often
enough, change the Span setting to change the cycle time.
1. To see the current Span setting, press both the Humidity and
Speed buttons.
2. To change the Span setting, Press and hold both the
Humidity and Speed buttons for 3 seconds. The LED Display
will flash the current Span Setting.
3. Press the Speed button to change the Span setting. Set the
Span to 3 to increase the humidifier’s run time. Set the Span
to 1 to decrease the humidifier’s run time.
4. When the LED Display shows your desired Span setting,
release the Speed button. After two seconds, the Span is set
and the LED Display will show the relative humidity.
Press the NiteGlo™ button on the Control Panel to turn the
night light on and off.
NOTE: The NiteGlo™ night light is inoperable when the
humidifier is turned off.
The NiteGlo™ Night Light
Refilling The Water Tank
1. When the water tank level is low, turn the humidifier ‘OFF’,
and unplug.
2. Remove the tank and take it to the sink or tub to refill.
3. Turn the tank upside down and unscrew the tank cap by
turning it counterclockwise. Empty the tank, refill with fresh
cool water (never use hot water), and replace the tank cap.
Be sure not to overfill the tank as water damage may occur
to furniture or flooring due to spillage. HUNTER WILL NOT
ACCEPT RESPONSIBILITY FOR DAMAGE TO PROPERTY
CAUSED BY WATER SPILLAGE.
4. Carry the tank back to the humidifier. Turn the tank upright
and place it on the humidifier. Be sure that the tank is seated
properly in the Tray. If the tank is properly located on the
Tray, you will see air bubbles flowing up into the tank.
Many regions have hard water with high concentrations
of minerals. When water evaporates from The Hunter
®
Evaporative Humidifier, minerals may be left behind. These
minerals can form a hard white scale which can be removed by
following the cleaning instructions. The frequency of cleaning
due to mineral build up can vary depending upon the quality
of water you may have. Refer to Figure 1 for part names.
1. Turn the humidifier ‘OFF’ and unplug the unit.
2. Lift the Main Housing as shown in Figure 5. The motor is
attached to the main housing. Do not place the motor near
water.
Figure 5
Grasp here
Humidifier Maintenance