Filter
Top Products
Owner’s Manual Room Air Heat Pump with R-410A Heat Controller, Inc.
13
15
■ To ensure proper operation, aim the remote
control at the signal receiver on the air
conditioner.
■ The remote control signal has a range of
up to 20 feet.
Remote Control
Cool Mode
Use the Coolmode at Low, Med, High orAuto Fan
Speed for cooling. Use the Temperature Increase ▲
/Decrease ▼pads to set the desired temperature
between
°F and 86°F in 1°F increments.
The compressor will cycle on and off to keep the
room at the set level of comfort.
Set the thermostat
at a lower number and the indoor air will become
cooler. Set the thermostat at a higher
number and
the indoor air will become warmer.
NOTE:If the air conditioner is off and is then turned on
while set to a Cool setting or if turned from a fan setting
to a Coolsetting, it may take approximately 3 minutes
for the compressor to start and cooling to begin.
Fan Only Mode
Energy Saver Mode
Auto Fan Speed
In the case of a power outage or interruption, the
unit will automatically re-start in the settings last
used after the power is restored. If the
Power Outage Recovery Feature
Controls the fan.
ON—The fan will cycle on and off with the
compressor. This results in wider variations of
room temperature and humidity. Normally used
when the room is unoccupied. NOTE: The fan may
continue to run for a short time after the compressor cycles off.
OFF—The fan runs all the time, while the
compressor cycles on and off.
Set to Auto fan speed for the fan speed to auto-
matically set to the speed needed to provide opti-
mum comfort settings with the set temperature.
If the room needs more cooling, the fan speed
will automatically increase. If the room needs less
cooling, the fan speed will automatically decrease.
Use the Fan Only Mode at Low, Med or Highfan
speed to provide air circulation and filtering
without cooling. Since fan only settings do not
provide cooling, a Set temperature cannot be
entered. The room temperature will appear
in the display.
Delay OFF—When the air conditioner is on,
it can be setto automatically turn off in
to
24 hours.
How to set:
Press the Delay –24hr pad on the unit or
the pad on the remote control. Each
touch
of the Increase ▲/ Decrease ▼ pads on the
unit or the Increase
+ / Decrease – pads on
the remote control will set the timer in
The Set light will turn on
while setting.
To review the remaining time on the Delay
–24hrtimer, press the Delay –24hr pad on the
unit or the pad on the remote control.
Use
the Increase ▲ / Decrease ▼ pads on the unit
or the Increase
+ / Decrease – pads on the
remote control to set a new time if desired.
To cancel the timer, press the Delay –24hrpad
until the light on the Delay –24hr pad goes off.
■ Make sure nothing is between the air conditioner
and the remote control that could block the
signal.
■ Make sure batteries are fresh and installed
correctly as indicated on the remote control.
Cooling Descriptions
For Normal Cooling—Select the Cool mode and
High or Med fan with a middle set temperature.
For Maximum Cooling—Select the Cool mode
and High fan with a lower set temperature.
For Quieter & Nighttime Cooling—Select the
Cool mode and Low fan with a middle set
temperature.
NOTE:Auto Fan Speed cannot be used when in the
Fan Only Mode.
feature was set, it will resume countdown. You may
need to set a new time if desired.
NOTE:Auto Fan Speed cannot be used when in the
Fan Only Mode.
Heat Mode (On some models)
Use the Heat mode at Low, Med, High or Auto Fan
Speed for heating. Use the
Temperature Increase
/Decrease
pads to set the desired temperature
between 61°F and 86°F in 1°F increments.
0.5
0.5 hour or 1hour intervals(the intervals is
0.5 hour as the delay timer below 10 hours;
the intervals is 1 hour as the delay timer
above 10 hours)
61
This time delay is required to protect the compressor.
Timer/Delay OFF—When the air conditioner is on,
Timer
Timer
Timer
Timer
Timer
0.5
0.5
0.5
0.5
0.5
Timer/Delay0.5-24hr
TIMER
0.5-24HR
DELAY
TIMER
0.5-24HR
DELAY