Filter
Top Products
Heat Controller, Inc. Room Air Heat Pump with R-410A Owner’s Manual
12
14
Controls
Mode Pad
Use to set the air conditioner to Cool,
Energy Saver,Fan Only Heat (on some
models) mode.
or
control panel indicate the selected settings.
Delay
Delay timer
Decrease
Mode select
Fan speed
Decrease
Temperature
set Increase
and Decrease
Remote Control
Delay timer Increase
Auto Fan on
Fan speed Increase
Unit power on/off
Air Conditioner Controls
Light indicates the
delay timer is set.
Set
Temp / Delay
Fan Only
Energy Saver
Cool
Heat
Med
High
Low
Auto
Speed
Fan
Power
Power Pad
Turns air conditioner on and off.
Lights next to the touch pads on the air conditioner
Operating your air conditioner properly helps you to obtain the
best possible results.
This section explains proper air conditioner operation.
IMPORTANT:
■ If you turn off the air conditioner, wait at least 3 minutes
before turning itback on. This preventsthe air conditioner
from blowing a fuse or tripping a circuit breaker.
■
Do not try to operate your air conditioner in the cooling mode
when outside temperature is below 61°F (16°C). Do not try to
operate your air conditioner in the heating mode when outside
temperature is over 86°F (30°C). The inside evaporator coil
will freeze up, and the air conditioner will operate properly.
NOTE: Inthe event of a power failure,your air conditioner will
operate at the previous settings when the power is restored.
1-24hr
Delay
Mode
Display
Delay Timer Increase ▲
(+) /Decrease ▼
(Æ-)Pads
Each touch of the Increase▲ / Decrease ▼
pads on the unit or theIncrease+/ Decrease –
pads on the remote control will set the delay
time when using the Delay –24hrtimer .
The Set light will turn on while setting.
Fan Speed Pads
Use to set the fan speed to Low, Med, High
or Autoon the unit. NOTE:On the remote
control, use the fan speed Increase+ /
Decrease
– pads to set the fan speeds to
Low,Med or High. Use the Auto pad to
turn Auto fan on.
Delay Pads
Delay ON—When the air conditioner is off, it
can be set to automatically come on in to
hours at its previous mode and fan settings.
Operating Controls(For Electronic units)
The display shows the set temperature when
in Heat/Cool/Energy Saver mode. Shows time
remaining on the delay timer. Shows the room
temperature when in Fan Only mode.
Light indicates the unit
is in the temperature or
delay time Set mode.
Shows the set temperature when in
Heat/Cool/Energy Saver mode.Shows
time remaining on the delay timer.
Shows the room temperature when
in Fan Only mode.
The Set light will
turn on while setting.
0.5
24
Do not try to operate your air conditioner in the cooling mode
when outside temperature is below 61°F (16°C). Do not try
to operate your air conditioner in the heating mode when
outside temperature is over 86°F (30°C). Otherwise, the
inside evaporator coil will freeze up, and the air conditioner
will operate properly.
Controls
Mode Pad
Use to set the air conditioner to Cool,
Energy Saver,Fan Only Heat (on some
models) mode.
or
control panel indicate the selected settings.
Delay 1–24hr
Delay timer
Decrease
Mode select
Fan speed
Decrease
Temperature
set Increase
and Decrease
Remote Control
Delay timer Increase
Auto Fan on
Fan speed Increase
Unit power on/off
Power Pad
Turns air conditioner on and off.
Lights next to the touch pads on the air conditioner
Operating your air conditioner properly helps you to obtain the
best possible results.
This section explains proper air conditioner operation.
IMPORTANT:
■ If you turn off the air conditioner, wait at least 3 minutes
before turning itback on. This preventsthe air conditioner
from blowing a fuse or tripping a circuit breaker.
■
Do not try to operate your air conditioner in the cooling mode
whenoutsidetemperatureisbelow61°F(16°C).Donottryto
operate your air conditioner in the heating mode when outside
temperature is over 86°F (30°C). The inside evaporator coil
will freeze up, and the air conditioner will operate properly.
NOTE: Inthe event of a power failure,your air conditioner will
operate at the previous settings when the power is restored.
Display
Shows the set temperature when in Heat/
Cool/Energy Saver mode. Shows time
remaining on the delay timer. Shows
the room temperature when in Fan Only
modes. The Set light will turn on while
setting.
Temp Increase ▲ /Decrease ▼ Pads
Use to set temperature when in Heat(on some
models)/Cool/Energy Savermode. The Setlight
will turn on while setting.
Delay Timer Increase ▲ (+) /Decrease ▼
(Æ-)Pads
Each touch of the Increase▲ / Decrease ▼
pads on the unit or theIncrease
+/ Decrease –
pads on the remote control will set the delay
time when using the Delay 1–24hrtimer ( ).
The Set light will turn on while setting.
Fan Speed Pads
Use to set the fan speed to Low, Med, High
or Autoon the unit. NOTE:On the remote
control, use the fan speed Increase
+ /
Decrease
– pads to set the fan speeds to
Low,Med or High. Use the Auto pad to
turn Auto fan on.
TIMER Pads
TIEMR ON—When the air conditioner is off, it
can be set to automatically come on in 0.5 to 24
hours at its previous mode and fan settings.
Operating Controls(For Electronic units)
12
Set
TIMER
SWING
-
FAN
SPEED
MED
HIGH
LOW
AUTO
POWER
COOL
FAN ONLY
HEAT
MODE
0.5-24 HR
ENERGY SAVER
TEMP/TIMER
+
Light indicates the
delay timer is set.
Light indicates the unit
is in the temperature or
delay time Set mode.
Air Conditioner Controls
Swing
Light indicates
SWING is on.
SWING Pad
Turn on to provide continuous side-to-side
air circulation. For fixed side-to-side air
direction,turn on until the desired air
direction is obtained,then turn it off.
The display shows the set temperature
when in Heat/Cool/Energy Saver mode.
Shows time remaining on the delay timer.
Shows the room temperature when in
Timer/Delay Pads
Timer/Delay On —When the air conditioner is off, it
Timer/Delay
0.5-24hr
0.5
Temp Increase ▲ /Decrease ▼ Pads
Use to set temperature when in Heat
The Set light will turn on while setting.
(on some models)/Cool/Energy Saver
Press Increase(+) and Decrease (-) Pads
at the same time for 3 seconds,Temperature
display will change between ∞
o
ÑF and
o
C.