Filter
Top Products
ProDuct sPeciFications
ProDuct sPeciFications
SS-GME8 www.goodmanmfg.com 5
airFlow Data
0.1 0.2 0.3 0.4 0.5 0.6 0.7 0.8
CFM CFM CFM CFM CFM CFM CFM CFM
GME8
0703BXC*
T1 1½ 875 59 793 65 736 70 674 77 592 88 556 509 460
T2 2 1,032 50 965 54 914 57 861 60 810 64 756 712 659
T3 2½ 1,217 43 1,153 45 1,098 47 1,051 49 1,009 51 964 918 877
T4 3 1,365 38 1,313 39 1,268 41 1,221 42 1,172 44 1,129 1,086 1,054
T5 3½ 1,549 33 1,505 34 1,460 36 1,420 37 1,378 38 1,350 1,305 1,268
GME8
0905CXC*
T1 2½ 1,268 53 1,198 56 1,151 58 1,092 61 1,041 64 988 932 883
T2 3 1,362 49 1,305 51 1,261 53 1,212 55 1,170 57 1,121 1,074 1,021
T3 3½ 1,576 42 1,519 44 1,473 45 1,426 47 1,398 48 1,341 1,290 1,252
T4 4 1,755 38 1,711 39 1,657 40 1,627 41 1,579 42 1,548 1,502 1,463
T5 5 2,183 31 2,128 31 2,094 32 2,060 32 2,014 33 1,992 1,944 1,847
GME8
1155CXC*
T1 3 1,466 58 1,415 60 1,357 63 1,306 65 1,248 68 1,202 1,144 1,088
T2 3½ 1,642 52 1,596 53 1,552 55 1,499 57 1,449 59 1,388 1,352 1,306
T3 4 1,750 49 1,750 49 1,707 50 1,667 51 1,610 53 1,574 1,531 1,486
T4 4 1,870 46 1,805 47 1,782 48 1,737 49 1,701 50 1,656 1,606 1,571
T5 5 2,297 37 2,297 37 2,224 38 2,106 40 2,014 42 1,896 1,813 1,669
¹ @ 0.5” ESP
• CFM in chart is without lter(s). Filters do not ship with this furnace, but must be provided by the installer. If the furnace requires two return lters,
this chart assumes both lters are installed.
• All furnaces ship as high-speed cooling and medium-speed heang. Installer must adjust blower cooling and heang speed as needed.
• For most jobs, about 375 - 400 CFM per ton when cooling is desirable.
• INSTALLATION IS TO BE ADJUSTED TO OBTAIN TEMPERATURE RISE WITHIN THE RANGE SPECIFIED ON THE RATING PLATE.
• This chart is for informaon only. For sasfactory operaon, external stac pressure should not exceed value shown on the rang plate.
• The above chart is for U.S. furnaces installed at 0-2000 feet. At higher altudes, a properly derated unit will have approximately the same
temperature rise at a parcular CFM, while ESP at the CFM will be lower.
• Factory Motor Speed Seng: T1 = 1st Stage Ht, T2 = 2nd Stage Ht, T5 = Cooling
• Tempertaure rise data is based on 2nd-stage heat. First-stage heat is 75% of rise indicated above.