Filter
Top Products
660
110
335
880 O/A
44
2143
628
628
335
2098
880
660
13
110
13
126
The above information is to assist you in your choice of a suitable Gazco fire. This is not intended to be all the information required to install your fire.
This can be obtained from your local Gazco retailer or you can download the full installation instructions from the Gazco website at www.gazco.com
44
STUDIO ICON OPEN FRONTED (mm)
STUDIO ICON GLASS FRONTED (mm)
STUDIO OPTIONS AND ACCESSORIES
Open Fronted Studio Fires
Product Code Description
Studio 1
8714GBK Black Granite linings
8713 Flue gather*
Studio 2
8715GBK Black Granite linings
Studio 3
8716GBK Black Granite linings
*Flue gather automatically included with Open Fronted Studio 2 and Studio 3 Fires.
Glass Fronted Studio Fires
8572 Warm air ducting kit (2 outlets)
8524 Balanced flue kit - vertical
Studio 1
8727CFEK01 Edge fitting kit for conventional flue
8727BFEK01 Edge fitting kit for balanced flue
8727CFCW01 Cool Wall fitting kit for conventional flue
8727BFCW01 Cool Wall fitting kit for balanced flue
8534 Balanced flue kit - up and out
Studio 2
8727CFEK02 Edge fitting kit for conventional flue
8727BFEK02 Edge fitting kit for balanced flue
8727CFCW02 Cool Wall fitting kit for conventional flue
8727BFCW02 Cool Wall fitting kit for balanced flue
8509 Balanced flue kit - up and out
Studio 3
8727BFEK03 Edge fitting kit for balanced flue
8727BFCW03 Cool Wall fitting kit for balanced flue
8567 Balanced flue kit - up and out
Studio 22
8727BFEK22 Edge fitting kit for balanced flue
8727BFCW22 Cool Wall fitting kit for balanced flue
8708 Balanced flue kit - rear
8534 Balanced flue kit - up and out
STUDIO ICON FRAME SIZES
504mm
O/A FLANGE
O/A FLANGE
146mm
1029mm
1163mm
264mm
21mm
186mm
1175mm
O/A
1029mm
84mm
81mm
162mm
423mm
283mm
158mm
STUDIO 22 APPLIANCE
DIMENSIONS (mm)
127
The above information is to assist you in your choice of a suitable Gazco fire. This is not intended to be all the information required to install your fire.
This can be obtained from your local Gazco retailer or you can download the full installation instructions from the Gazco website at www.gazco.com
GLASS FRONTED STUDIO EDGE INSTALLATION OPTIONS
Edge Kit – this kit is screw-mounted to the front flange of the outer firebox.
The L-shaped attachments can either provide a 20mm return against which high
temperature plasterboard/screed can be butted up for the ‘clean edge’ look or, if
the firebox flange is on the outside of a brick or studwork wall, allow ceramic or
stone tiles to be fixed with a similar look. The Edge Kit is finished in black to
complement the Studio.
Cool Wall Kit – again, screw-mounted to the front flange of the outer firebox,
the 60mm deep U-shaped attachments of the Cool Wall kit are designed primarily
for studwork false chimney breasts. The additional depth allows some of the
heat to be vented up into the void above the firebox and then re-enter the room
at a higher level. The effect is to produce a cooler wall immediately above the
appliance than would otherwise be the case. The Cool Wall Kit is left unfinished so
that it can be painted to match the front face of your fireplace.
Installation method for studwork/false
chimney breast application
Edge Kit
Installation method for brick/masonary
chimney breast application
Convected heat flows
directly out into room
Convected heat flows
directly out into room
Cool Wall Kit
Installation method for studwork/false
chimney breast application
Installation method for brick/masonary
chimney breast application
Convected heat flows up
through an open channel and
can be vented back into room
at a higher point
Convected heat flows up
through an open channel
and can be vented back
into room at a higher point
NB: When using the Edge Kit, heat resistant board and high temperature
finishing plaster must be used. Please refer to installation instructions
for full details.
NB: Full installation information, including the requirement for the use of non-
combustible materials, can be downloaded from www.gazco.com
When using the Edge Kit the fire is recessed by 20mm from the finished
wall surface and the kit is finished in black to complement the Studio.
When using the Cool Wall Kit the fire is recessed by 60mm from the finished
wall surface and the kit is left unfinished so that it can be painted to match
your decor.