Filter
Top Products
2
INSTALLATION, Continued
See “Avoiding Dead Air Spaces” for more information.
NOTE: For any location, make sur
e no door or other obstruction could keep
carbon monoxide or gas fr
om reaching the Alarm.
This unit should r
eceive continuous electrical power. (The battery is
meant for emer
gency back-up only). Choose an outlet where it can’t be
accidentally unplugged or switched off by children. Keep small children
away fr
om the unit. Teach them not to play with it or unplug it. Explain
what the alar
ms mean.
WHERE THIS ALARM SHOULD NOT BE INSTALLED
T
o avoid causing damage to the unit, to provide optimum protection, and
to prevent unnecessary alarms, Do NOT locate this Alarm:
• In garages, kitchens, crawl spaces and unfinished attics. Avoid extremely
dusty
, dirty or greasy areas. Installation in these areas could lead to
nuisance alarms, may expose the sensor to substances that could damage
or contaminate it, or the Alarm may not be heard by persons in other
ar
eas of the home, especially if they are sleeping.
• In the garage, vehicle exhaust can contain some carbon monoxide. These
levels are higher when the engine is first started. Within hours of starting a
vehicle and backing it out of the garage, the levels pr
esent over time can
activate the Alarm and become a nuisance.
• In the kitchen, some gas appliances can emit a short burst of CO or gas
upon start-up. This is normal. If your Explosive Gas/CO Alarm is installed
too close to these appliances, it may alarm often and become a nuisance.
• Keep units at least 20 feet (6 meters) from the sources of combustion
particles (stove, fur
nace, water heater, space heater) if possible. In areas
where a 20-foot (6m) distance is not possible – in modular, mobile, or
smaller homes, for example – it is recommended the Alarm be placed
as far fr
om these fuel-burning sources as possible. The placement
recommendations are intended to keep these Alarms at a reasonable
distance from a fuel-burning source, and thus reduce “unwanted” alarms.
Unwanted alarms can occur if an Alarm is placed directly next to a fuel-
burning source. Ventilate these areas as much as possible.
If you must
install the Alarm near a cooking or heating appliance, install at least
5 feet (1.5 meters) from appliance.
• In extremely humid areas. This Alarm should be at least 10 feet (3 meters)
from a shower, sauna, humidifier, vaporizer, dishwasher, laundry room,
utility room, or other source of high humidity.
• In direct sunlight.
• In turbulent air, like near ceiling fans or open windows. Blowing air may
prevent CO or gas from reaching the sensors.
• In areas where temperature is colder than 40˚ F (4˚ C) or hotter than
100˚ F (38˚ C). These areas include non-airconditioned crawl spaces,
unfinished attics, uninsulated or poorly insulated ceilings, porches, and
garages.
• Less than 12 inches (305 mm) away from fluorescent lights. Electrical
“noise” can interfere with the sensor.
• In “dead air” spaces. See “Avoiding Dead Air Spaces”.
AVOIDING DEAD AIR SPACES
“Dead air” spaces may prevent gas from reaching the Alarm. To avoid dead
air spaces, follow installation recommendations below.
On ceilings, install Alarms as close to the center of the ceiling as possible.
If this is not possible, install the Alarm at least 4 inches (102 mm) from the wall
or cor
ner.
For wall mounting, the top edge of Alarms should be placed between
6 inches (152 mm) and 12 inches (305 mm) fr
om the wall/ceiling line.
On a peaked, gabled, or cathedral ceiling, install Alarm within 3 feet (0.9
meters) of the peak of the ceiling, measured horizontally.
BEFORE YOU BEGIN INSTALLATION
Since CO generally mixes well with air, mounting the Alarm will depend on the
type of explosive gas you intend to detect. If you are not certain which type of
gas you are using in your home, please read about natural gas and propane in
“Wher
e to Install this Alarm”.
• Make sure the alarm is not receiving excessively noisy power.
Examples of noisy power could be major appliances on the same
circuit, power from a generator or solar power, light dimmer on the
same cir
cuit or mounted near fluorescent lighting. Excessively noisy
power may cause damage to your Alarm.
Find the pair of self-adhesive labels included with this Gas/CO Alarm.
• On each label write in the phone number of your emergency responder
(like 911) and a qualified appliance technician.
• Place one label near the Gas/CO Alarm, and the other label in the “fresh
air” location you plan to go if the alarm sounds.
SECURING THE POWER CORD TO AN OUTLET
DISCONNECT POWER TO THE OUTLET TO A
VOID ELECTRICAL SHOCK.
1.
Remove the wallplate scr
ew fr
om the outlet and hold the wallplate in position.
2.
Plug the power cor
d into the wall outlet so that the scr
ew hole lines up with
the wallplate screw hole.
3.
Insert the scr
ew thr
ough the power cord screw hole and into the wallplate
screw hole.
4. Tighten screw in place and restore power to the outlet.
3.875 inches
Mounting Guide Template
3 7/8 inches (98mm)
3.875 inches
HOW TO INST
ALL THIS GAS/CO ALARM
IMPOR
TANT! Read all instructions before using this product.
T
ools you will need:
Scr
ewdriver, drill.
1.
Determine the best location for your Gas/CO Alarm.
2.
Your Alarm is equipped to be mounted as a corded unit (recommended
for natural gas detection), a direct plug unit (recommended for propane
gas detection). The unit can be plugged dir
ectly into a wall outlet. If your
outlets are mounted horizontally, refer to “If Outlet is Mounted Horizontally
(Sideways)”.
If the adapter is taken out of the unit, the Alarm can be installed high on
the wall, while the adapter is plugged into a wall outlet. The explosive gas
you use will determine if the Alarm should be installed high on the wall
(AC cor
d option) or low on the wall (direct plug option).
ACTIVATING THE BATTERY BACK-UP
Activate the battery back-up by installing the battery. The battery is for
back-up only and is not intended to power the Alar
m for an extended
period of time in the absence of AC.
The Alarm will light-up the display briefly to indicate the unit is receiving power.
DIRECT PLUG ALARM INTO AN OUTLET (for Propane Detection)
This Alarm can be plugged directly into a wall outlet located close to the floor.
This is the r
ecommended configuration for detecting propane.
1.
Choose a standard UNSWITCHED 120V AC outlet.
2. Plug Alarm in.
IF OUTLET IS MOUNTED HORIZONTALLY (SIDEWAYS)
If you ar
e going to use your Alarm as a direct plug into an outlet that is
mounted horizontally (sideways), you may want to rotate the adapter 90º,
as follows:
1. With back of unit facing you (AC blades on your left), place your left
thumb on adapter release and grab AC blades with your right hand to
release the left side.
2. Repeat for the other side adapter thumb release. This will allow adapter
to slide out.
3. Remove adapter.
4. Rotate the adapter 90º and snap firmly back into place.
5. Plug Alarm into AC outlet.
WALL MOUNTED ALARM (for Natural Gas Detection)
Installation tips for power cord models: The power cord option provides
more flexibility in mounting locations and allows the Alarm to be easily
installed at or above eye level.
NOTE: If you mount the Alarm high on a wall, make sure it is between 6 to 12
inches (152-305 mm) down from the ceiling. Any higher than this, it will be
in “dead air” space and carbon monoxide or natural gas may not reach the
sensors.
NOTE: Do not cover the Alarm with a curtain.
To install for a wall-mount, you will need to pull out the removable adapter and
power cord, as follows:
1.
Repeat steps 1 to 3 as described above in
“to r
otate the adapter”
.
2. With adapter out, pull out power cord and unwrap it.
3. Insert the screws provided until head is approx. 1/8 inch (3 mm) from wall
(if mounting in plaster board or drywall, drill 3/16 inch (5 mm) hole and use
plastic anchor provided). Use mounting guide template to locate holes as
shown in diagram below.
4. Hook the Alarm over the screw onto the keyhole in back of unit.
5. Plug power cord into AC outlet.