Filter
Top Products
PROBLEM SOLVING GETTING TO KNOW YOUR CANISTER VACUUM
This appliance was inspected thoroughly and was in good operating condition when it
was shipped from the factory. If a minor problem occurs, it usually can be solved quite
easily when the cause is found. Therefore, this checklist is provided for your
convenience.
PROBLEM POSSIBLE CAUSE POSSIBLE
Cleaner Won’t Run
1. Not firmly plugged in.
2. No electricity in wall outlet.
3. On/Off switch not turned on.
4. Thermal protector tripped.
5. Blown fuse/tripped breaker.
1. Plug in firmly, push on/off switch
to on.
2. Check fuse or breaker.
3. Push on/off switch to on
4. Reset thermal protector.
5. Reset circuit breaker or replace
fuse.
Cleaner Won't Pick
Up
1. Full or clogged dust cup.
2. Clogged nozzle or dust cup port.
3. Clogged hose.
4. Hole in hose.
5. Hose not inserted fully.
6. Motor protection system activated.
7. Dirty filters.
8. HEPA filter needs cleaning or
replacing.
9. Debris screen needs cleaning.
1. Clean dust cup.
2. Remove obstruction.
3. Remove obstruction.
4. Replace hose.
5. Push hose in securely.
6. Reset thermal protector.
7. Clean / change filters.
8. Clean or replace HEPA filter.
9. Clean debris screen.
Air Flow Restricted
With Attachment
Use Sound Changes
1. Attachment use restricts airflow.
2. New carpet trimmings clogging air
passage.
1. Check attachment.
2. Remove obstruction.
ORDERING REPLACEMENT DUST CUP FILTERS
1. On/Off Button
2. Cord Rewind Button
3. Carrying Handle
4. Dust Cup (Container)
5. Dust Cup Handle
6. Dust Cup Full Indicator
7. Hose Connector Inlet
8. Hose Connecting Power Cord
9. Hose Connecting Power Cord
10. Hose Connector
11. Flexible Hose
12. Receptacle For Motorized Brush
Power Cord
13. Motorized Brush Power Cord
14. Telescopic Tube
15. Motorized Brush
16. Motorized Brush On/Off Button
17. Head Light
18. Floor-to-carpet Brush
19. Upholstery Brush
20. Crevice Tool
21. Furniture Guard
TO ORDER REPLACEMENT FILTERS OR FOR TECHNICAL
SUPPORT
HEPA Filter Item # XF732H
for Model FM732H
Call: 1 (800) 275-9251
Monday to Friday 8:30 A.M. - 5:00 P.M. Eastern Standard Time
Please Note:
The HEPA Dust Cup Filter may be washed. We recommend that this be done once a
month or when suction appears reduced. To wash your HEPA Dust Cup Filter, hold
filter cartridge by frame flange and rinse under a tap until all observable dirt has been
removed. Some discoloration of the HEPA filter material may occur, this is normal and
will not affect the filter's performance. When finished, shake off excess water. Do NOT
wash in dishwasher. It is important that when you wash the HEPA dust cup filter, you
allow it to dry COMPLETELY before using it again. We recommend 24 hours to air
dry. DO NOT DRY IN DRYER. We recommend replacing the HEPA filter every three
(3) to six (6) months, depending on the amount of use to ensure peak performance of
your vacuum.
IMPORTANT
: The Pre-Motor filter and Post Motor filter should be replaced every 6
months or sooner if required. It is important that when you wash the HEPA dust cup
filter, pre-motor filter or the exhaust filter you allow them to dry COMPLETELY before
using again. We recommend 24 hours to air dry. DO NOT DRY IN DRYER.
All filters should be checked regularly for signs of damage, preferable after each
cleaning task. The filters must be replaced immediately if they become damaged.
Always disconnect the vacuum from the electrical outlet when checking the filters.
* Illustrations may differ from actual product.
Technical Specifications
Main Unit: Voltage: 120V., 60Hz.
Power: 10.3 Amps
With Motorized Power Head
: Voltage: 120V., 60 Hz.
Power: 12 Amps
2
9