Filter
Top Products
List Price CUSL-31
Effective: December 4, 2006
(Supersedes CUSL-30)
UNDER SHELVES (#16-Gauge)
For use under drainboards arranged for
bolting to support legs.
WHEN WIDTH IS:
Add for each up to 27 1/2" $340.00 per ft.
linear foot 28" to 33 1/2" 442.00 per ft.
Add for additional leg support as required,
refer to #18.
ADD FOR EACH RETURN END
4" high . . . . . . . . . . . . . . . . . . .$175.00
8" high . . . . . . . . . . . . . . . . . . . .240.00
12" high . . . . . . . . . . . . . . . . . . .290.00
16" high . . . . . . . . . . . . . . . . . . .363.00
PARTIAL COLUMN CUT
Add following flat charges for this condition:
Unit has no backsplash . . . . . . . . .$232.00
Unit has 4" back (or less) . . . . . . . .311.00
Unit has back over 4" . . . . . . . . . . .462.00
FULL COLUMN CUT
Add following flat charges for this condition:
Unit has no backsplash . . . . . . . . .$385.00
Unit has 4" back (or less) . . . . . . . .549.00
Unit has back over 4" . . . . . . . . . . .788.00
FINISHED BACKSPLASH
Finishing off exposed backs
or ends up to 4" high by 26"
in length (or less) add . . . . . . . . . .$430.00
Each added inch of length . . . . . . . . .10.00
Backs or ends over 4" and up to
8" by 26" in length (or less) add . . .496.00
Each added inch of length . . . . . . . . .12.00
INSIDE ANGLE CUTS
Following flat extra charge applied to flat or
raised rim tops.
INSIDE “L” corner angle up
to 6" long . . . . . . . . . . . . . . . . . .$385.00
Add for each additional inch . . . . . .48.00
OUTSIDE ANGLE CUTS
Following flat extra charge applied to flat or
raised rim tops.
At corner where there is a backsplash
and/or return end . . . . . . . . . . . .$317.00
At corner where there is NO
backsplash
and/or return end . . . . . . . . . . . . .140.00
PARTIAL NOTCHING OF
BACKSPLASH
Partial cutout of backsplash as shown in
this example...
add flat charge of ....................$187.00
OUTSIDE RADIUS CORNERS*
Add the following flat charges to flat or
raised rim tops:
Up to 1" radii . . . . . . . . . .$96.00 $96.00
Over 1" to 3" radii . . . . . . .N/A 135.00
Add per inch over
3" radii . . . . . . . . . . . . .N/A 28.00
1/2" circle end, up to
15" radii . . . . . . . . . . . .N/A 704.00
*Not available with feature #17 or #7.
DROP-IN RANGE OPENING
For cutting and reinforcing opening in top
deck to receive rectangular gas or electric
range...
add flat charge of ........................$304.00
(Be sure to furnish manufacturer’s name
and complete model number)
NUTONE CUTOUT
Cutout top deck to receive NuTone power
unit, location optional. (Be sure to provide
clearance of 6 3/4" under counter area at
this location)...
add flat charge of...........................$241.00
ELECTRICAL CUTOUT
For cutting back with opening to receive
one to four gang electric or switch box...
add flat charge of . . . . . . . . . . . . .$73.00
COVED TYPE CORNERS
Coved corners where top surface meets
backsplash (and/or ends), 1/4" radius is
standard (no extra charge).
1/2" or 3/4" radii at back only . . . .$197.00
1/2" or 3/4" radii at each
return end . . . . . . . . . . . . . . . . . .100.00
1/2" or 3/4" radii at each
partial column cut . . . . . . . . . . . .100.00
1/2" or 3/4" radii at each
full column cut . . . . . . . . . . . . . . .197.00
SHORTER BACKSPLASH OR RETURN
ENDS
Where backsplash or return end is shorter
than sink length or width...
add flat charge of ........................$144.00
FULL NOTCHING OF
BACKSPLASH
Full cutout of backsplash as shown in this
example...
add flat charge of ........................$249.00
LOWER/HIGHER BACKSPLASH OR
RETURN ENDS
Where return end is lower or higher than
height of backsplash of sink or counter
top...in addition to charge for return end...
add flat charge of ........................$119.00
BULL NOSE FRONT/SIDE EDGE
OF TOP
Bull nose offered with 3/4" radius
(1-1/2" Dia.) on front and/or sides in
place of standard 1-1/2" turn down.
Bull nose is normally provided without
a raised rim edge.
If required with standard 5/32" raised
rim feature, bowls need to be located
4" from front and/or side edge of top.
In either above rim condition…
add flat charge of ....................$385.00
Exposed end or
back finished
Corner cove
10 3/8"
4 5/8"
1234
5678
910
13 14 15 16
11 12
All dimensions are in inches. To convert to millimeters, multiply inches by 25.4.
6
W/RIM FLAT
PARTIAL COLUMN CUT
FULL COLUMN CUT
{
CCuussttoomm FFeeaattuurreess PPrriiccee SScchheedduullee