Filter
Top Products
2928
Questions and AnswersTimer Changing the
Message Display
Language
Error Messages
Normal. Timer: Auto
Select time?
English
Select language?
Error: #7
Check
bumper
See manual
Timer
It is possible to set the time duration for
Normal or Quick vacuuming.
1. Select the desired vacuum programme and
press to confirm.
2. Use until “On” is displayed and confirm
by pressing .
3. Set the desired time duration using and
confirm by pressing . (For normal
vacuuming, this is the time vacuuming
lasts, i.e. not including wall mapping.)
4. Put Trilobite on the floor and start
vacuuming by pressing .
Language
Trilobite can show display messages in
English or Swedish.
1. To change the display language, switch on
Trilobite and press .
2. The display will ask whether you want to
change the programme. Ignore this and
press .
3. The display will ask whether you want to
change the time setting. Ignore this and
press .
4. The display will ask whether you want to
change the language. Press .
5. Press to select the desired language
and confirm by pressing .
Trilobite will now show display messages
in the selected language.
Status Messages
When you select a function, a status
message is shown on the display for
about seven seconds.After this, the name
of the function is shown again. It is of
course possible to change or confirm a
displayed function even while the status
message is shown.
Error Messages
The only faults that you can rectify
yourself are the ones listed below. In the
event of other error messages, recharge
and restart your Trilobite. If it still does
not start, contact our Customer Service
on 020-53 53 50.
The errors you can correct yourself are
presented below:
5. Check roller.
Is something stuck? Is it incorrectly
attached?
6 Check casters.
Is something stuck?
7 Check bumper.
Verify its spring action. Is something stuck
preventing it from moving?
12 Trilobite is stuck.
Move it and switch it on again. Also see
Normal Vacuuming on page 4.
15 Check dust cassette.
In most cases, the filter unit has probably
not been set or it is incorrectly set.
16 Check charger.
Is the charger connected to the mains?
Are the terminals on the charger and
Trilobite properlyconnected to each other?
21 Moisture on the circuit board.
Let the machine dry out for 12 hours.
Then try restarting it.
Should I pay attention to anything special when I vacuum a
room for the first time?
It is a good idea to be present when the room is vacuumed the first
time, for example to see if it takes unnecessary time for Trilobite to
navigate around furniture.
Can I use Trilobite in a room with an activated alarm?
Yes, if it has a “pets monitoring” facility.
Can I hide the magnetic strips under e.g. a carpet?
Yes, as long as it not thicker than 15 mm.
What is the purpose of the audible signals?
They confirm that a command or measure has been correctly
received or to advice a problem.
Trilobite operates at different speeds. Is something wrong?
Not at all. The speed varies depending e.g. on the layout and
furniture in the room.
Is it all right to always leave Trilobite connected to the charger
when it is not is use?
Yes, but make sure children cannot start it by mistake.
Is it necessary to switch off Trilobite before charging it?
No.
How can I know whether I have placed Trilobite correctly
during manual battery charging?
A battery symbol lights in the display and you hear an audible signal.
Why doesn’t it charge?
1. Check that Trilobite is correctly connected to the charger
(see the question above).
2. Check that the charger has been connected to the mains.
Is it dangerous to touch the charging terminals?
No. They have no power in the output mode and carry max. 28 V in
the input mode.
Why does Trilobite sometime pause for approximately 10
seconds during vacuuming?
1. Trilobite uses two battery packs. It will briefly pause when
switching from one battery pack to the other.
Why does Trilobite stop completely during vacuuming?
1. Check that it has been sufficiently charged. See page 24.
2. Did it find the charger during wall mapping?
3. The time duration for vacuuming may need to be increased.
See page 28.
Why does Trilobite crackle while vacuuming?
This sound is produced by the navigation system.
Why do I need to replace the filter so often?
The filter is actually one of the most important components in the
machine. It collects all dust, even very small dust particles (this is
why you should also use original Electrolux filters). Just like a dust
bag becomes full, so does the filter. There is no dust bag in the
Trilobite, but the filter is always a necessity.
If Trilobite starts to smell bad, what could this be due to?
Probably the dust filter was not replaced.
What should I do when an error message is displayed?
The error messages you can correct yourself are shown on page 28.
In all other cases, contact Customer Service by calling 020-53 53 50.
What is the Cable Protection System?
This is simply a system that prevents Trilobite from getting stuck in
electric cords on the floor.
What is the Trilobite Stairsafe system?
This is a safety measure that prevents Trilobite from falling down
staircases when they have been cordoned off with the magnetic
strips.
Do I need to vacuum myself also?
Sometimes this may necessary no matter which vacuum programme
you use, especially in corners or along the walls in the room.