Filter
Top Products
8
1. SPARK ARRESTOR MUFFLER OR SPARK ARRESTOR MUFFLER WITH CATALYST - The mufer or
catalytic mufer controls exhaust noise and emission. The spark arrestor screen prevents hot, glowing particles of
carbon from leaving the mufer. Keep exhaust area clear of ammable debris.
2. CARRYING HANDLE - The carrying handle is used to transport the pump.
3. SPARK PLUG - Provides spark to ignite fuel mixture.
4. CHOKE LEVER - Choke lever is located at the top of the air cleaner.
- Move choke forward to CLOSE (Starting Position) ( )
- Move to OPEN (Run Position) ( )
5. AIR CLEANER - Contains replaceable felt element. Should be inspected and cleaned as necessary or daily.
6. STARTER HANDLE - Pull handle slowly until starter engages then pull quickly and rmly. When engine starts,
return handle slowly. DO NOT let handle snap back or damage to unit can occur.
7. PRIMER BULB - Pumping primer bulb before starting engine draws fresh fuel from the fuel tank priming the
carburetor for starting. Pump primer bulb until fuel is visible and ows freely in the clear fuel tank return line. Pump
bulb an additional 4 or 5 times.
8. FUEL CAP - Covers and seals fuel tank. Securely tighten fuel cap after refueling.
9. IGNITION SWITCH - “Toggle Switch”mounted on engine. Move Toggle UP to Run. Move Toggle DOWN to
Stop.
10. PUMP STAND - Pump stand supports pump. Always place pump on a rm, level site as near to the water source as
possible. Make sure pump will not move due to vibration and/or the weight of suction hose when full of water.
11. PUMP HOUSING - Seals the water from air and has suction and discharge ports. The housing holds water after the
pump is stopped, eliminating the need for priming at the next start up.
12. DRAIN PLUG - Drains water from pump housing for storage.
13. SUCTION PORT - Suction hose attaches to port.
14. DISCHARGE PORT - Discharge hose attaches to port. Accepts 25 mm (1 inch) hose coupling or 25 x 19 mm
(1 x 3/4 inch) Garden Hose adaptor (included with pump).
15. PRIME PORT PLUG - Used to prime or ll the pump housing with water prior to initial start up. Pump is self
priming in subsequent operations. Never operate pump without water, otherwise pump seals will fail.
16. THROTTLE LEVER - Controls engine speed. Move lever towards engine for idle position. Move lever toward
pump housing for fast run position.
17. SEALING WASHER - Seals hose connector against pump port. Unit comes with two washers - one for suction
hose connector, one extra.*
18. HOSE FITTING - Unit comes with two ttings - one for suction hose - one extra.* When assembling, install clamp
onto hose, connecter onto hose, then press tting into hose.
19. HOSE CONNECTER - Connecter threads directly onto 1 inch pump ports. Unit comes with two connecters - one
for suction hose - one extra.*
20. HOSE CLAMP - Unit comes with three - one for clamping suction hose connecter tting - one for strainer - one
extra.*
21. SUCTION HOSE - 25 mm (1 inch) inner diameter, 3 m (10 ft.) length. Longer hose up to 7.5 m (24 ft.) can be at-
tached.
22. STRAINER - Strainer prevents foreign material larger than 5/16 inch diameter from entering and damaging the
pump. Always have strainer attached onto suction hose when operating the pump.
23. GARDEN HOSE ADAPTER - Adaptor steps down from 25 mm thread to 3/4 inch and allows household garden
hose to be utilized as discharge hose.
* Extrahosettingsareforusewith25mm(1inch)dischargehosewhichisnotsupplied.