DeWalt DW904 Home Safety Product User Manual


  Open as PDF
of 6
 
FIG. 1
LENS HOLDER
PORTE-LENTILLE
SUJETADOR DE
LA LENTE
BULB
AMPOULE
BOMBILLA
BATTERY RELEASE BUTTON
BOUTON DE DÉGAGEMENT DE LA PILE
BOTON DE LIBERACION DE LA BATERIA
POWER PACK (NOT
INCLUDED)
ENSEMBLE DE PILES
(NON COMPRIS)
BATERIA (NO INCLUIDA)
SWIVELING HEAD
TÊTE PIVOTANTE
CABEZA GIRATORIA
SWITCH
INTERRUPTEUR
INTERRUPTOR
FIG. 3
SPARE BULB STORAGE
RANGEMENT DE
L’AMPOULE DE RECHANGE
COMPARTIMIENTO
PARA BOMBILLA DE
REPUESTO
FIG. 2
the battery terminals are protected and well insulated from materials that could
contact them and cause a short circuit.
Charging Procedure
DANGER: Electrocution hazard. 120 volts present at charging terminals. Do
not probe with conductive objects. Danger of electric shock or electrocution.
1. Plug the charger into an appropriate outlet before inserting battery pack.
2. Insert the battery pack into the charger. The red (charging) light will blink
continuously indicating that the charging process has started.
3. The completion of charge will be indicated by the red light remaining ON
continuously. The pack is fully charged and may be used at this time or left
in the charger.
DW9115 (15 MINUTE CHARGER) ONLY
1. Plug the charger into an appropriate AC power outlet. The charger will beep
twice and the red light will blink and then go off.
2. Insert the battery pack into the charger, making sure the pack is fully
seated in the charger. The red light will blink and the charger will beep once
indicating the charging process has started.
3. The battery pack will be fully charged in less than 15 minutes under most
conditions. This will be indicated by the red light remaining ON and 3
audible beeps. The pack is fully charged and may be used at this time or
left in the charger.
Installing and Removing the Battery Pack
To insert the power pack into your worklight, slide it into the end of the light until
it snaps into place. To remove the power pack, depress the release buttons
shown and withdraw the power pack.
Switch
To turn the light on, slide the switch forward. To turn it off, slide the switch back.
Swiveling Head (Fig. 1, 2)
Your worklight has a swiveling head. To convert your light to a right angle
model, grasp the front end of the light forward of the switch and hold the back
end firmly. Twist the front end clockwise (as viewed from the lens) until the
head swivels 90 degrees and clicks into place. To return the head to a straight
position, rotate the head (as viewed from the lens) counterclockwise until it
clicks into the straight position.
Replacing the Light Bulb
Worklight Cat. No Replacement Bulb Cat. No.
DW902 DW9023
DW904 DW9043
DW906 DW9063
DW908 DW9083
To replace the light bulb, first unscrew the lens holder. Pull the bulb out of the
spring, and insert a new bulb. Reinstall lens holder.
NOTE: Do not look directly into the worklight beam.
Spare Bulb Storage (Fig. 3)
To store a bulb, unscrew the lens holder and remove it. Inside the body of the
worklight is the storage socket. To remove the bulb, pull it up and out of the
storage area.
NOTE: Removing a pack from the charger and immediately inserting it into the
worklight may weaken bulb life.
The RBRC™ Seal
The RBRC™ (Rechargeable Battery Recycling Corp oration)
Seal on the nickel cadmium, nickel metal hydride or lithium ion
batteries (or battery packs) indicate that the costs to recycle
these batteries (or battery packs) at the end of their useful life
have already been paid by D
EWALT. In some areas, it is illegal to place spent
nickel cadmium, nickel metal hydride or lithium ion batteries in the trash or
municipal solid waste stream and the RBRC program provides an environmentally
conscious alternative.
RBRC™ in cooperation with D
EWALT and other battery users, has established
programs in the United States and Canada to facilitate the collection of spent
nickel cadmium, nickel metal hydride or lithium ion batteries. Help protect our
environment and conserve natural resources by returning the spent nickel
cadmium and nickel cadmium, nickel metal hydride or lithium ion batteries to
an authorized D
EWALT service center or to your local retailer for recycling. You
may also contact your local recycling center for information on where to drop
off the spent battery.
RBRC™ is a registered trademark of the Rechargeable Battery Recycling
Corporation.
Repairs
The charger is not serviceable. There are no serviceable parts inside the
charger.
Lampes de travail
MODÈLES DW902 (9,6 V), DW904 (12 V), DW906 (14,4 V) ET
DW908 (18 V)
– Utiliser avec des ensembles de piles et des chargeurs DEWALT
(vendus séparément).
POUR TOUT RENSEIGNEMENT SUR L’OUTIL OU TOUT AUTRE OUTIL
DEWALT, COMPOSER SANS FRAIS LE:
18004-DEWALT (1800 433-9258)
NOTE: La lampe de travail, modèle DW902, s’alimente à l’aide d’un ensemble
de piles de 9,6 volts. La lampe de travail, modèle DW904, s’alimente à l’aide
d’un ensemble de piles de 12 volts. La lampe de travail, modèle DW906,
s’alimente à l’aide d’un ensemble de piles de 14,4volts. La lampe de travail,
modèle DW908, s’alimente à l’aide d’un ensemble de piles de 18 volts. Les
ensembles de piles sont vendus séparément.
To assure product SAFETY and RELIABILITY, repairs, maintenance and
adjustments (including brush inspection and replacement) should be
performed by a D
EWALT factory service center, a DEWALT authorized
service center or other qualified service personnel. Always use identical
replacement parts.
Three Year Limited Warranty
DEWALT will repair, without charge, any defects due to faulty materials or
workmanship for three years from the date of purchase. This warranty does
not cover part failure due to normal wear or tool abuse. For further detail of
warranty coverage and warranty repair information, visit www.dewalt.com
or call 1-800-4-D
EWALT (1-800-433-9258). This warranty does not apply to
accessories or damage caused where repairs have been made or attempted
by others. This warranty gives you specific legal rights and you may have other
rights which vary in certain states or provinces.
In addition to the warranty, D
EWALT tools are covered by our:
1 YEAR FREE SERVICE
D
EWALT will maintain the tool and replace worn parts caused by normal use,
for free, any time during the first year after purchase.
90 DAY MONEY BACK GUARANTEE
If you are not completely satisfied with the performance of your D
EWALT
Power Tool, Laser, or Nailer for any reason, you can return it within 90 days
from the date of purchase with a receipt for a full refund – no questions asked.
LATIN AMERICA: This warranty does not apply to products sold in Latin
America. For products sold in Latin America, see country specific warranty
information contained either in the packaging, call the local company or see
website for warranty information.
FREE WARNING LABEL REPLACEMENT: If your warning labels become
illegible or are missing, call 1-800-4-D
EWALT for a free replacement.
 previous next