Filter
Top Products
15
104352
OWNER’S MANUAL
WARNING: Make sure the re-
mote selector switch is in the
OFF position when you are away
from home for long periods of
time. Heater will come on auto-
matically with remote selector
switch in the ON position.
Ignitor Electrode
Pilot Burner
Figure 26 - Pilot
TO TURN OFF GAS
TO APPLIANCE
MANUAL LIGHTING
PROCEDURE
1. Follow steps 1 through 6 under Light-
ing Instructions, page 14.
2. Depress control knob and light pilot
with match.
3. Keep control knob pressed in for 30
seconds after lighting pilot. After 30
seconds, release control knob. Now
follow step 9.
1. After lighting, let pilot flame burn for
about one minute. Turn control knob
to ON position. Adjust flame adjust-
ment knob anywhere between HI
and LO. Slide the remote selector
switch to the REMOTE position (see
Figure 27). The burners will come on.
You can now turn the burners on and
off with the hand-held remote con-
trol unit.
IMPORTANT
: Do not leave the re-
mote selector switch in the RE-
MOTE position when the pilot is not
lit. This will drain the battery.
GHRC Operation:
2. Press the ON button to turn the
burners on and the Off button to turn
the heater to pilot.
GHRCT Operation:
2. Select the MANUAL or AUTO but-
ton on the hand-held remote control
unit (GHRCT only, see Figure 28).
• In MANUAL mode, turn burners
on or off by pressing the ON or
OFF buttons on the hand-held re-
mote control unit. (This is the only
function with GHRC.)
NOTICE: You must light the pilot
before using the hand-held re-
mote control unit. See
Lighting
Instructions
on page 14.
Continued
OPERATING
FIREPLACE
Continued
Shutting Off Heater
1. Turn control knob clockwise
to the OFF position.
2. Set remote selector switch in the OFF
position.
Shutting Off Burners Only (pilot
stays lit)
You may shut off the burners and keep
the pilot lit by doing one of the following:
• Turn control knob clockwise
to the PILOT position.
• Use remote control manual OFF button.
• Set remote selector switch in the OFF
position.
OPTIONAL REMOTE
OPERATION
Thermostat Control Operation
(Optional GHRCT Only) The thermo-
stat control setting on the remote control
unit can be set to any comfort level be-
tween HI and LO. The Burners will turn
on and off automatically to maintain the
comfort level you select. The ideal com-
fort setting will vary by household de-
pending upon the amount of space to be
heated, the output of the central heating
system, etc.
For wall thermostat operation, follow in-
struction supplied with thermostat ac-
cessory GWMT1. For wall switch opera-
tion follow instructions supplied with
GWMS2.
Note:
All remote control accessories must
be purchased separately (see Accessories,
page 21). Follow instructions included
with the remote control.
O
F
F
P
I
L
O
T
O
N
L
O
I
H
ON
OFF
REMOTE
TEMP
STATUS
HI
LO
MAN ON
AUTO OFF
Increases Room
Temperature
Decreases Room
Temperature
Turns Burners
On and Off
Shows Current
Operation Mode
Shows Temperature
Setting
Allows Burners to be
Turned On and Off
with the Hand-Held
Remote Unit.
The log heater will
automatically cycle
between pilot and the
heat setting that has
been selected.
Figure 28 - Thermostat Hand-Held Remote Control Unit Selections
Figure 27 - Setting the Remote Selector Switch, Control Knob, and
Flame Adjustment Knob for Remote Operation
Remote Selector Switch in Remote
Position(Optional Remote Control)
Control Knob in
On Position
Flame Adjustment Knob