Filter
Top Products
111252-01E
For more information, visit www.desatech.com
For more information, visit www.desatech.com
26
OPERATING FIREPLACE
Continued
OPERATING FIREPLACE
Optional Hand-Held Remote Operation
O
F
F
P
I
L
O
T
O
N
L
O
I
H
ON
OFF
REMOTE
ON
OFF
Blower Control Knob
(Optional Accessory)
Variable
Control Knob
Selector Switch
in Remote
Position
Gas Control Knob
in ON Position
Figure 53 - Setting the Selector Switch, Gas Control Knob, and
Variable Control Knob for Remote Operation
After lighting, let pilot flame burn for about one minute. Turn
control knob to ON position. Adjust flame adjustment knob
anywhere between HI and LO. Slide the selector switch to the
REMOTE position (see Figure 53).
Note:
The burner may light
if hand-held remote was on when selector switch was last turned
off. You can now turn the burner on and off with the hand-held
remote control unit.
IMPORTANT:
Do not leave the selector switch in the REMOTE
or ON position when the pilot is not lit. This will drain the
battery.
ON/OFF SERIES (MODELS GHRCB AND
CGHRCTB)
Hold the control button on the hand-held remote until burner
turns on. Hold the control button again until burner turns off
(see Figure 54).
TO LOCK press both buttons on hand-held remote control until
light stops flashing. Hand-held remote control is now locked. If
the fire is on it will be turned off automatically. In the locked state,
the light will not light up when any button is pressed.
TO UNLOCK press both buttons together on hand-held remote
control until the light stops flashing. The hand-held remote is
now unlocked.
THERMOSTAT SERIES (MODELS GHRCTB
AND CGHRCTB)
The hand-held remote can be operated using either the manual
mode (MANU) or thermostatic mode (AUTO) (see Figure 55). To
select Fahrenheit/Centigrade mode display, carefully press the ˚C/
˚F mode button with the end of a paper clip or similar blunt object.
Manual Mode
1. Press the POWER and LOCK buttons together to turn on
the hand-held remote control.
2. Press the MANU button to turn on the fireplace.
3. Press the POWER and LOCK buttons together to turn off
the fireplace.
Auto (Thermostatic) Mode
1. Press the POWER and LOCK buttons together to turn on
the hand-held remote control.
2. Press AUTO button to select this mode.
3. Set the desired room temperature by pressing the TEMP +
or - buttons.
4. Press the POWER and LOCK buttons together to turn off
the fireplace
Note:
Do not leave the hand-held remote in the AUTO mode
close to the fireplace. The radiant heat from the fireplace will
turn off the fireplace. Ideally, place the hand-held remote in the
center of the room facing towards the fireplace.
Note:
Do not hold the hand-held remote for a long time. Body
temperature will affect its operation in the AUTO mode.
Safety Features
When away from home for an extended period of time or as a
child safety feature to prevent accidental ignition of the fire-
place, the receiver ON/OFF/REMOTE switch should be in the
OFF position.
Note:
All remote control accessories must be purchased sepa-
rately (see Accessories, page 39). Follow instructions included
with the remote control.
OPTIONAL HAND-HELD
REMOTE OPERATION
NOTICE: You must light the pilot before using the
hand-held remote control unit. See
Lighting Instruc-
tions
on page 25.
Figure 54 - On/Off Hand-Held Remote Control Unit (C)GHRCB
Control Button
Turns Burners
On and Off
Figure 55 - Thermostat Hand-Held Remote Control Unit (C)GHRCTB
Turns Hand-Held
Remote On or Off and
Allows You to Choose
the Manual Setting
Selects Auto Setting
Increases Room
Temperature in AUTO
Mode
Locks System to
Prevent Accidental
Ignition
Digital Display
Shows
Temperature and
Settings
Turns Burners
On or Off
Decreases Room
Temperature in
AUTO Mode