Filter
Top Products
27
104558
OWNER’S MANUAL
O
F
F
P
I
L
O
T
O
N
L
O
I
H
ON
OFF
REMOTE
ON
OFF
TEMP
STATUS
HI
LO
MAN ON
AUTO OFF
1. After lighting, let pilot flame burn for
about one minute. Turn gas control
knob on the control valve to ON po-
sition. Turn variable control knob
anywhere between HI and LO. Slide
the selector switch to the REMOTE
position.
Note:
The burner(s) may
light if hand-held remote ON button
was on when selector switch was last
turned off. You can now turn the
burner(s) on and off with either op-
tional hand-held remote control unit.
IMPORTANT:
Do not leave the se-
lector switch in the REMOTE posi-
tion when the pilot is not lit. This will
drain the battery.
IMPORTANT:
Be sure to press the
ON/OFF buttons on the hand-held
remote control unit for up to 3 sec-
onds to assure proper operation.
GHRC Series Operation:
2a. Press the ON/OFF button to turn the
burner(s) on and off. When turning
burner(s) off, the pilot will remain lit.
GHRCT Series Operation:
2b. Select the MAN (manual) or AUTO
button on the hand-held remote con-
trol unit (see Figure 59).
• In manual mode, turn burner(s) on
or off by pressing the ON or OFF
buttons on the hand-held remote
control unit.
• In auto mode, the room tempera-
ture is controlled by the thermo-
stat in the hand-held remote con-
trol unit. To increase the room tem-
perature, press the top arrow of the
TEMP button. To lower the room
temperature, press the bottom ar-
row of the TEMP button. At higher
settings the heater will run more.
IMPORTANT:
This remote control
has been specially engineered to
take an air temperature sample
every 5.5 minutes in the auto mode.
It will not respond immediately to
the temperature setting being
turned up or down.
OPERATING
FIREPLACE
Continued
Increases Room
Temperature
Decreases Room
Temperature
Turns Burners
On and Off
Shows Current
Operation Mode
Shows Temperature
Setting
Allows Burners to be
Turned On and Off
with the Hand-Held
Remote Unit.
The Heater will
Automatically Cycle
between Pilot and the
Heat Setting that has
been Selected.
Figure 59 - Hand-Held Thermostat Remote Control Unit Selections
(GHRCT Only)
OPERATING
OPTIONAL BLOWER
ACCESSORY
Locate the blower controls by opening
the lower louver panel on the fireplace.
Blower controls are located on the left
side of the switch bracket to the left just
inside the louver panel.
Both the GA3700 manual blower and the
DA3610T thermostatically-controlled
blower have an ON setting and an OFF
setting. The blower will only run when the
switch is in the ON position. In the OFF
position, the blower will not operate.
Note for DA3610T Only:
If you are
using DA3610T blower with optional ther-
mostat (wall mount or remote control)
for the fireplace, your fireplace and
blower will not turn on and off at the
same time. The fireplace may run for
several minutes before the blower turns
on. After the heater modulates to the pilot
position, the blower will continue to run.
The blower will shut off after the firebox
temperature decreases.
The blower helps distribute heated air
from the fireplace. Periodically check the
louvers of the firebox and remove any
dust, dirt, or other obstructions that will
hinder the flow of air.
Figure 58 - Setting the Selector Switch,
Gas Control Knob, and Variable Control
Knob for Remote Operation
Control Selector Switch in
Remote Position (Optional
Remote Control)
Gas Control
Knob in On
Position
Variable
Control Knob
Blower Control Knob
(Optional Accessory)
Continued
IMPORTANT:
The hand-held re-
mote control unit must be near the
heater but not extremely close to it.
The thermostat on the hand-held
remote control unit will heat up too
quickly and turn the heater off.
3. Use the STATUS button on the hand-
held remote control unit to see the
operation mode being used and the
temperature setting selected. A red
light will come on beside the opera-
tion mode being used.
4. To turn the burner(s) off when oper-
ating in the manual mode, press the
OFF button. If operating in the auto
mode, press the MAN button, then
press the OFF button. The pilot will
remain lit.
IMPORTANT:
To turn the
pilot off, manually turn the gas con-
trol knob on the heater to the OFF
position or set selector switch to OFF
position.