Desa FVFM27NR/PR Gas Heater User Manual


 
108382-01D
16
For more information, visit www.desatech.com
For more information, visit www.desatech.com
BURNER FLAME PATTERN
Figure 29, page 17, shows a correct burner flame pattern. Figure 30,
page 17, shows an incorrect burner flame pattern.
If burner flame pattern is incorrect as shown in Figure 30, page 17
turn heater off (see To Turn Off Gas to Appliance, page 15)
see Troubleshooting, pages 18 through 20
OPERATING HEATER
Continued
Figure 26 - Thermostat Hand-Held Remote Control Unit Selec-
tions (GHRCTA only)
Figure 25 - Setting the Selector Switch, Control Knob, and
Flame Adjustment Knob for Remote Operation
Selector Switch in Remote Position
(Optional Remote Control)
ON
OFF
REMOTE
O
F
F
P
I
L
O
T
O
N
L
O
I
H
Control Knob in
On Position
Flame Adjustment Knob
Figure 27 - Correct Pilot
Flame Pattern (Propane/LP
Pilot Shown)
Pilot Burner
Thermocouple
Increases Room
Temperature in
AUTO Mode
Decreases Room
Temperature in
AUTO Mode
Turns Burners
On or Off and
Allows You to
Choose the Auto
Setting
Shows Tempera-
ture Setting
The Log Heater
will Automatically
Cycle between
Pilot and the Heat
Setting that has
been Selected
INSPECTING BURNERS
Check pilot flame pattern and burner flame patterns often.
PILOT FLAME PATTERN
Figure 27 shows a correct pilot flame pattern. Figure 28 shows an
incorrect pilot flame pattern. The incorrect pilot flame is not
touching the thermocouple. When the thermocouple cools, the
heater will shut down.
If pilot flame pattern is incorrect, as shown in Figure 28
turn heater off (see To Turn Off Gas to Appliance, page 15)
see Troubleshooting, pages 18 through 20
Pilot Burner
Thermocouple
Figure 28 - Incorrect Pilot Flame
Pattern (Propane/LP Pilot
Shown)
OPERATION
Optional Remote Operation (Cont.)
INSPECTING BURNERS
Pilot Flame Pattern
Burner Flame Pattern
IMPORTANT:
Do not leave the selector switch in the RE-
MOTE position when the pilot is not lit. This will drain the
battery.
IMPORTANT:
Be sure to press the ON/OFF buttons on the
hand held remote control unit for up to 3 seconds to assure
proper operation.
GHRC Series Operation:
2a. Press the ON/OFF button to turn the burner on and off.
When turning burner off, the pilot will remain lit.
GHRCTA Series Operation
2b. Press the AUTO/ON/OFF button on the hand-held remote
control (see Figure 26). The lights to the left of the button
will show AUTO, ON, or OFF.
In the ON mode, the burners will ignite. The heater is in
manual mode when ON is lit.
In the AUTO mode, the thermostat in the hand-held re-
mote unit controls the room temperature. To increase the
room temperature, press the top arrow of the TEMP but-
ton. To lower the room temperature, press the bottom
arrow of the TEMP button. At higher settings the heater
will run longer.
IMPORTANT:
This remote control has been specially en-
gineered to take an air temperature sample every 5.5
minutes in the AUTO mode. It will not respond immedi-
ately to the temperature setting being turned up or down.
IMPORTANT:
The hand-held remote control unit must
be near the heater. Do not keep the hand-held remote
control unit too close to the heater. The thermostat on
the hand-held remote control unit will heat up too quickly
and turn the heater off.
3. To turn the burner off, press the AUTO/ON/OFF button
until OFF lights. The pilot will remain lit.
IMPORTANT:
To turn the pilot off, manually turn the con-
trol knob on the heater to the OFF position.