Filter
Top Products
27
To Open the Door Manually
The door should be fully closed
if possible. Pull down on the
emergency release handle and
lift the door manually. To
reconnect the door to the
opener, press the door control
push bar.
The lockout feature prevents the
trolley from reconnecting
automatically. Pull the
emergency release handle down
and back (toward the opener).
The door can then be raised
and lowered manually as often
as necessary. To disengage the
lockout feature, pull the handle
straight down. The trolley will
reconnect on the next UP or
DOWN operation, either
manually or by using the door control or
remote.
Trolley
Release
Arm
NOTICE
Emergency
Release
Handle
(Pull Down)
Trolley
Release
Arm
NOTICE
Emergency
Release
Handle
(Down and Back)
To prevent possible SERIOUS INJURY or DEATH from a falling
garage door:
• If possible, use emergency release handle to disengage
trolley ONLY when garage door is CLOSED. Weak or broken
springs or unbalanced door could result in an open door
falling rapidly and/or unexpectedly.
• NEVER use emergency release handle unless garage doorway
is clear of persons and obstructions.
• NEVER use handle to pull door open or closed. If rope knot
becomes untied, you could fall.
LOCKOUT POSITION
MANUAL DISCONNECT
POSITION
Using the Wall-Mounted Door Control
THE MULTI-FUNCTION DOOR CONTROL
Press the push button to open or close the door. Press
again to reverse the door during the
closing cycle or to stop the door while it's
opening.
Light feature
Press the Light button to turn the opener
light on or off. It will not control the
opener lights when the door is in motion. If you turn it on
and then activate the opener, the light will remain on for
4-1/2 minutes. Press again to turn it off sooner. The 4-1/2
minute interval can be changed to 1-1/2, 2-1/2, or 3-1/2
minutes as follows: Press and hold the Lock button until
the light blinks (about 10 seconds). A single blink indicates
that the timer is reset to 1-1/2 minutes. Repeat the
procedure and the light will blink twice, resetting the timer
to 2-1/2 minutes. Repeat again for a 3-1/2 minute interval,
etc., up to a maximum of four blinks and 4-1/2 minutes.
Lock feature
Designed to prevent operation of the door from
hand-held remote controls. However, the door will open
and close from the Door Control, the Outside Keylock and
the Keyless Entry Accessories.
To activate, press and hold the Lock button for 2 seconds.
The push bar light will flash as long as the Lock feature is
on.
To turn off, press and hold the Lock button again for
2 seconds. The push bar light will stop flashing. The Lock
feature will also turn off whenever the “learn” button on the
motor unit panel is activated.
Additional features when used with the 3-Button hand-
held remote
A) To control the opener lights:
In addition to operating the door, you may
program the remote to operate the lights.
1. With the door closed, press and hold a small remote
button that you want to control the light.
2. Press and hold the Light button on the
Multi-Function door control.
3. While holding the Light button, press and hold the Lock
button on the door control.
4. After the opener lights flash, release all buttons.
LOCK
LIGHT
Push
Button
Lock
Button
Light
Button
B) To operate one door using all three buttons on the
hand-held remote:
You may program the remote to
open the door with the large button,
close it with the middle button, and
stop the door’s movement with the
third button.
NOTE: If remote is already programmed, you must first
erase all codes. See Programming.
1. With the door closed, press and hold the large remote
push button.
2. Press and hold the Lock button on the door control.
3. Press and hold the door control push bar.
4. After the opener lights flash, release all buttons.
Open
Close
Stop