Filter
Top Products
27
To Open the Door Manually
The door should be fully closed if
possible. Pull down on the emergency
release handle and lift the door
manually. To reconnect the door to the
opener, press the door control push
bar.
The lockout feature prevents the trolley
from reconnecting automatically. Pull
the emergency release handle down
and back (toward the opener). The
door can then be raised and lowered
manually as often as necessary. To
disengage the lockout feature, pull the
handle straight down. The trolley will
reconnect on the next UP or DOWN
operation, either manually or by using
the door control or remote.
To prevent possible SERIOUS INJURY OR DEATH from a
falling garage door:
• If possible, use emergency release handle to disengage
trolley ONLY when garage door is CLOSED. Weak or broken
springs or unbalanced door could result in an open door
falling rapidly and/or unexpectedly.
• NEVER use emergency release handle unless garage doorway
is clear of persons and obstructions.
• NEVER use handle to pull door open or closed. If rope knot
becomes untied, you could fall.
Trolley
Release
Arm
NOTICE
Emergency
Release
Handle
(Pull Down)
Trolley
Release
Arm
NOTICE
Emergency
Release Handle
(Down and Back)
LOCKOUT POSITION
MANUAL DISCONNECT POSITION
Using the Wall-Mounted Door Control
THE MULTI-FUNCTION DOOR CONTROL
Press the push button to open or close the
door. Press again to reverse the door during the
closing cycle or to stop the door while it’s
opening.
Light feature
Press the Light button to turn the opener light
on or off. It will not control the opener lights when the door is in
motion. If you turn it on and then activate the opener, the light
will remain on for 4-1/2 minutes. Press again to turn it off sooner.
The 4-1/2 minute interval can be changed to 1-1/2, 2-1/2, or 3-1/2
minutes as follows: Press and hold the Lock button until the light
blinks (about 10 seconds). A single blink indicates that the timer
is reset to 1-1/2 minutes. Repeat the procedure and the light will
blink twice, resetting the timer to 2-1/2 minutes. Repeat again for
a 3-1/2 minute interval, etc., up to a maximum of four blinks and
4-1/2 minutes.
Lock feature
Designed to prevent operation of the door from hand-held remote
controls. However, the door will open and close from the Door
Control, the Outside Keylock and the Keyless Entry Accessories.
To activate, press and hold the Lock button for 2 seconds. The
push bar light will flash as long as the Lock feature is on.
To turn off, press and hold the Lock button again for 2 seconds.
The push bar light will stop flashing. The Lock feature will also
turn off whenever the “learn” button on the motor unit panel is
activated.
Additional features when used with the 3-Button hand-held
remote
A) To control the opener lights:
In addition to operating the door, you may
program the remote to operate the lights.
1. With the door closed, press and hold a small
remote button that you want to control the
light.
2. Press and hold the Light button on the Multi-Function door
control.
3. While holding the Light button, press and hold the Lock button
on the door control.
4. After the opener lights flash, release all buttons.
LOCK
LIGHT
Push
Button
Lock
Button
Light
Button
B) To operate one door using all three buttons on the hand-held
remote:
You may program the remote to open the
door with the large button, close it with the
middle button, and stop the door’s
movement with the third button.
NOTE: If remote is already programmed,
you must first erase all codes. See Programming.
1. With the door closed, press and hold the large remote push
button.
2. Press and hold the Lock button on the door control.
3. Press and hold the door control push bar.
4. After the opener lights flash, release all buttons.
Open
Close
Stop