Filter
Top Products
Step 1: Make sure trigger switch is not locked in the ON position.
Step 2: Plug the AC charger or DC charger/adapter into the socket located on
the base of the spotlight handle as illustrated.
Step 3: For DC Charger/Adapter:
Plug the other end of the DC charger/adapter into a cigarette lighter
receptacle.
For AC Charger:
Plug the other end of the AC charger into a wall outlet.
Step 4: Allow the spotlight to charge for at least 8 hours. Do not allow to
charge more than 12 hours.
Note: LED indicator on base of handle turns off automatically when battery
is fully charged.
Step 5: Remove spotlight from the charger before operating.
See chart for recommended charge times.
Continuous Beam Using Lock Button:
Step 1: For a continuous beam,depress trigger switch and slide the lock button
to the LOCKED position.
Step 2: To unlock and turn spotlight OFF,slide the lock button to the
UNLOCKED position.
NOTE: To lock the Dual Xenon in the OFF position, release trigger switch,then
slide the lock button to the LOCKED position.
WARNING: Always turn spotlight off when not in use.
Switching Between Single and Dual Beams:
Step 1: For single beam,slide switch on back of light to one dot, as illustrated.
Step 2: For dual beam,slide switch on back of light to two dots, as illustrated.
NOTE: The Dual Xenon will burn for approximately 40 minutes if using both
beams, or approximately 85 minutes if using only one beam.
To Operate
2
Trigger
Switch
LED Indicator
Lock
Button
Beam
Switch
Single
Beam
Dual
Beam
Unlocked
Locked
To Charge
40
4812
85
Battery Charge
USAGE (Minutes)
CHARGE TIME (Hours)
Charge Times
Charge time is dependent on usage of the
product. See chart below for recommended charge time.
IMPORTANT: The EPA
Certified RBRC
®
Battery
Recycling Seal on the
nickel cadmium (NiCd)
battery contained in our
product indicates The
Brinkmann Corporation is
voluntarily participating in an industry program
to collect and recycle these batteries at the end
of their useful life, when taken out of service in
the United States or Canada. The RBRC
®
program provides a convenient alternative to
placing used NiCd batteries into the trash or the
municipal waste stream, which may be illegal
in your area. Please call 1-800-8-BATTERY™ for
information on NiCd battery recycling and
disposal bans/restrictions in your area. The
Brinkmann Corporation’s involvement in this
program is part of our commitment to
preserving our environment and conserving our
natural resources.
INS-800-2200-B_DualXenon-bi.qxd 7/18/03 4:12 PM Page 3
3
Glass
Retainer
Rubber
Cap
To Replace Bulb
Only use Brinkmann xenon bulb that is designed for the Dual Xenon
spotlight as a replacement. Use of any other bulb may result in poor
performance and may damage your spotlight.
NOTE: Handling the bulb can leave oil from your fingers on the bulb.To
extend the life of the new bulb and maximize brightness, gently clean
off bulb with soft cloth or tissue.Make sure the reflector does not
touch or bend the bulb while replacing spotlight head.
Step 1: Disconnect spotlight from charger.
Step 2: Remove front rubber cap from barrel of spotlight.
Step 3: Pinch the wings of the glass retainer together and lift as illustrated.
Step 4: Pull glass and reflector away from rear housing.
Step 5: Pull old bulb straight out of bulb holder.
Step 6: Make certain that "legs" on new bulb are straight. Insert "legs" into
the two holes in the bulb holder.
Step 7: Gently push bulb straight in until fully seated and centered.
Step 8: To reassemble, place the glass and reflector on the rear housing.
Insert the glass retainer into the rear housing.
Step 9: Replace rubber cap.
WARNING: Do not touch the lamps when light is on or if it was recently on.
The lamps will be hot and could cause serious burns.
Glass &
Reflector
Rear
Housing
Tips to Avoid Damage to Your
Dual Xenon Spotlight
• Never attempt to wipe or clean the inner reflective surface of the reflector.
Touching or wiping the surface will damage it permanently.
• The lens is made of tempered glass.Avoid dropping or sharp impact on
spotlight to prevent damage.
• Do not allow hot lens to come in contact with water or materials subject to
heat damage.
• The spotlight is weather resistant.It is not waterproof. Do not use the
spotlight under water or store outdoors.
• Use only Brinkmann xenon bulb that is designed for your Dual Xenon
spotlight. Use of any other bulb may result in poor performance and may
damage your spotlight.
• After months of use,cigarette lighters can build up corrosion that may
prevent the DC lighter plug from making good contact. It may be necessary
to clean the inside of your cigarette lighter receptacle with a fine emery
cloth.Before cleaning receptacle,remove the fuse to prevent it from
shorting out.
The retractable hanging ring allows spotlight to hang while in use or
during storage.
To Hang/Store Dual Xenon
INS-800-2200-B_DualXenon-bi.qxd 7/18/03 4:12 PM Page 4