Filter
Top Products
3 4
FAN HEAD ASSEMBLY
Step 1. Attach the neck of the fan to the
upper extension pole. To do this, align
the extension pole clasps and screw
holes up with the corresponding holes
on the neck of the fan. Once you have
the neck adjusted to the angle of the
extension pole clasps, screw the clasps
to the neck of the fan until secure.
Step 2. Using your screwdriver, remove
the securing screw that is located inside
the Bionaire
®
decorative cap on the grill
ring. Once you have unscrewed the grill
ring, put it aside until you are ready to re-
attach the grills.
Step 3. Remove the two plastic ties that
are holding the rear grill and the fan blade together. Discard the two
plastic ties and cardboard.
Step 4. Loosen and take off the rear grill mounting nut ( H ) that is
attached to the motor housing by turning counter-clockwise.
Step 5. Place the rear grill on the front of the motor housing; making
sure that the handle on the back of the grill is above the motor housing
(doing this will align the holes on the grill over the two screws in the
housing). Then tighten the rear grill mounting nut onto the rear grill by
turning clockwise.
NOTE : To know that the rear grill is on correctly, there will be one grill
clip located at the bottom of the grill.
Step 6. Place the fan blade onto the motor shaft ( J ) making sure to
align the flat area on the motor shaft with the flat area in the center of
the fan blade. Slide the fan blade to the back of the motor shaft until it
stops and the motor shaft is protruding.
Step 7. Insert the washer and tighten the nut onto the motor shaft to
secure the fan blade. Complete the fan blade assembly by turning
the fan blade cap counter-clockwise into the matching grooves in the
center of the fan blade.
Step 8. Place the front grill onto the back grill so that the 2 clips on the
top of the front grill fit over the rear grill. Also ensure that the bottom
clip that is attached to the rear grill, attaches and fits onto the front grill
when assembling the fan head.
NOTE: When attaching the grill ring, make sure to have the Bionaire
®
decorative cap (where the two ends of the grill ring meet)
at the bottom, center of the grills.
Step 9. Place the grill ring around the edges of both grills making sure to
enclose both edges with the ring. Then re-attach the Bionaire
®
decorative
cap, by passing the screw through the hole on the side of the cap and
using your screwdriver tighten the grill ring together until the fan head
assembly is completely secure.
FINAL ASSEMBLY
Step 1. Insert the extension pole into the lower pole. Insert the two
brackets (Parts R and S) into the top of the lower pole. Make sure to align
the two rectangular plastic tabs with groove inside the pole. Slide the
brackets down until the pole cover is completely inserted into the lower
pole.
Step 2. Once inserted, tighten the screw on the top bracket until it is
secure. Then tighten the height adjustment knob to your desired height
(see below instructions for height adjustment).
Step 3. Pass the power cord though the power cord clip to
secure it into place.
OPERATING INSTRUCTIONS
Step 1. Set the fan base on a dry, level surface.
Step 2. Please make sure the Speed Control Knob is in the "Off" position.
Plug the cord into any standard 120V AC outlet.
Step 3. The SPEED is adjusted by moving the knob left or right to the
desired speed setting. The speeds are indicated by the numbers 1 for Low,
2 for Medium, and 3 for High.
Step 4. The OSCILLATION Knob is located on the bottom of the fan motor
housing. To start oscillation, pull knob down. To stop oscillation, push knob
up.
ADJUSTMENT INSTRUCTIONS
TILT ADJUSTMENT
Step 1. To change the tilting angle of the fan head, move the fan head to
the desired angle.
HEIGHT ADJUSTMENT
Step 1. Turn the height adjustment knob counter-clockwise and slide the
fan up or down to the desired position. Once you have reached your
desired height, turn the knob clockwise to lock into position.