Filter
Top Products
5
6
B. Remote is ON and Unit is ON:
1. Press the Mode button on the unit. The unit will
then switch “Modes”; either from “High” to “Med”,
“Med” to “Low”, or “Low” to “Off”. The unit’s lights
will reflect the change.
The Remote will display a different mode – the mode in which it
was left. If a button is pressed on the Remote, the Remote’s
signal will override the “Mode” on the unit and the two will be
back in sync.
TIMER FUNCTION:
Using Timer to Turn Unit Off
1) Hold mode button for 2 seconds to unlock remote.
2) Push + and - together.
2.1) "timer" turns on. 1 Hr appears on the screen.
3) Push + or - to adjust the number of hours the unit will run
before it automatically shuts itself off.
3.1) you can choose from; 1 to 8 hours
3.2) 1 through 8 will scroll in a continuous loop
4) After you have made your selection, the whole screen flashes
for 5 seconds after last button push of + or - then goes back
to previous mode
4.1) "timer" remains lit to show the timer function has
been set.
5) At any time if you unlock the remote and push the
mode button to turn the unit off, the timer
setting will be erased and "timer" will disappear from
the remote.
6) To check how much time is remaining, press and hold the +
and – buttons simultaneously.
Using Timer to Turn Unit On
This function is meant for a person to pre-humidify a room by
setting the timer. For Example: It’s 8 am, and you want to come
home to a humidified room at 8 pm. To accomplish this place
the unit in the desired room and set the timer to turn the unit on
in 12 hours. Once the timer is activated the unit will run for a
preset time of 2 hours.
1) Hold mode button for 2 seconds to unlock remote.
2) DO NOT push mode again as this will turn unit on.
3) Push + and - together.
3.1) Unit remains off.
3.2) "timer" and "auto - high" turns on and flashes on
the remote, and 1 Hr appears on the screen.
Note: Do not block ventilation openings on remote while in use,
this may affect the accuracy of the humidity reading.
HUMIDISTAT OPERATION WITH REMOTE
1. Press Mode button on remote until the remote screen
displays “Auto” and “High”. The “Set” humidity is
displayed next to the “Room” humidity. The “Auto” light
on unit will illuminate. The
unit will cycle on and off to
maintain the “Set” humidity
at high setting.
NOTE: The default room
humidity is 45%. In this
mode the unit will run to
maintain the “Set” humidity.
2. Press Mode button on remote
again for “Med” and “Auto”,
and again for “Low” and “Auto”. The unit will cycle on and
off to maintain the “Set” humidity at the designated setting.
3. To turn unit “Off”, press the Mode button and the LCD will go
blank (except for the “Room” humidity display which is
always displayed while batteries are in the remote) and the
unit will shut off.
Note: It is normal for the humidifier to cycle on and off as it
maintains the preset humidity.
Adjusting Set Humidity:
1. When in “Auto” mode, press the (+) or (-) buttons on the
remote. The “Set” number will increase or decrease with
each press. Hold the button down to scroll. The minimum
humidity is 35% and the maximum is 60%. The unit scrolls
one digit at a time in a continuous loop. 35%, 36%…, 59%,
60%, 35%, 36%….
UNIT OPERATION WITHOUT REMOTE
Your humidifier can be operated directly from the control panel
located on the top of the unit
A. Remote and Unit are OFF:
1. Press the Mode button on the unit the first time.
The “High” light illuminates and the unit runs in
“High” mode. The power light turns on.
2. Press the Mode button a second time to run in
“Med” mode.
3. Press the Mode button again to run in “Low” mode.
4. Press the Mode button again and the unit shuts off.
Note: The “auto” light only illuminates when the unit is
set to “auto” mode by the remote.
Mode
High
Fig 3
Filter Monitor
Med
Low
Auto
BCM6100U_Eng.qxd 8/14/02 5:41 PM Page 5