Filter
Top Products
3
4
beep every two seconds until it is synced with the remote.
To sync unit with remote follow the below steps:
Unlock remote. (This must be done before each use of the
remote) To Unlock remote, hold down the mode button for 2
seconds until the lock symbol disappears on the screen.
Once the remote is unlocked, press the mode button again and
the unit will quickly beep 5 times telling the user the signal was
received. If you have more than one humidifier, DO NOT SYNC
more than 1 unit at once.
Battery Replacement: If the batteries are running low on
power, a low battery indicator will appear on the remote.
Low batteries will affect transmission distance and the screen
contrast. We recommend replacing batteries immediately.
Remote Distance: The transmission distance for this remote
is approximately 30ft. Do not use farther than 30ft. from the
appliance. Remote must be used in same room as
appliance.
Communication Safety Check: Every minute while in Auto
mode, the Galileo™ Center communicates with the base unit.
If the Galileo™ Center goes out of range and/or has low batter-
ies, the communication will stop, and after 8 minutes of non-
communication the unit will shut off.
MANUAL OPERATION WITH REMOTE
1. Press Mode button on the remote. “High” illuminates on
remote screen indicating mode. The power light on the unit
will turn on. The unit turns on and operates in “High” mode.
The units “High” light will illuminate. In this mode, the unit will
continuously run at its high setting.
2. Press Mode button on remote a second time for “Med”
mode and once again for “Low” mode.
Note: While using the remote, the backlight function will turn on
when any button is pushed and will turn off after 10 seconds of
non-use.
mode
Fig 2
This device complies with Part15 of the FCC Rules. Operation is subject-
ed to the following two conditions: (1) this device may not cause harmful
interference, and (2) this device must accept any interference received,
including interference that may cause undesired operation.
HOW YOUR COOL MOISTURE HUMIDIFIER WORKS
Your Bionaire
®
Cool Moisture humidifier draws dry air through the front
air intake grill area. This air is then passed through a moisture–laden
wick filter which retains the minerals and deposits. The resulting moist
air is directed back into the room from the top air grill.
☛
Tip: This humidification system provides a cool, invisible moisture
output. It is normal not to see the mist.
PRE-OPERATING INSTRUCTIONS
1. Be sure the humidifier is
switched off and discon-
nected from the electrical
outlet.
2. Select a location for your
humidifier, on a flat surface,
about 4" away from the wall.
Do not place your humidifier
on furniture, a floor location
that will not be damaged by
moisture is best.
3. Remove the water tank, by
holding the tank handle
and lifting straight upwards.
4. Remove the filter door by
pulling the tab straight out. Check to see that the wick filter
is properly in place. Replace the humidifier filter door.
FILLING THE WATER TANK
1. Twist off the water tank cap located on the bottom of the
water reservoir by turning counter clockwise and fill the water
tank with cool, fresh water. Do not fill with warm water as this
may cause leaking.
2. After filling the water tank, replace the water tank cap by
firmly turning clockwise and then replace the water reservoir
on the base. The water reservoir will immediately begin to
empty into the base.
FIRST USE ONLY
1. Put batteries into Remote. The “Room” humidity will be
displayed at all times. (Use 3 AAA Alkaline batteries only, do
not mix batteries)
2. Plug unit into outlet. The first time the unit is plugged in, it will
Fig 1
A. Humidifier Tank
B. Carry Handle
C. Filter Monitor
D. Humidifier Housing
E. Filter Door
F. Humidifier Base
G. Control Panel
D
A
E
F
C
G
B
BCM6100U_Eng.qxd 8/14/02 5:41 PM Page 3