Filter
Top Products
27
It is recommended that lower water temperatures be used to avoid
the risk of scalding. It is further recommended, in all cases, that the
water temperature be set for the lowest temperature which satisfies
your hot water needs. This will also provide the most energy efficient
operation of the water heater.
Figure 26 shows the approximate water temperatures produced at
various thermostat settings. Short repeated heating cycles caused
by small hot water uses can cause temperatures at the point of use
to exceed the thermostat setting by up to 20°F (11°C). If you
experience this type of use you should consider using lower
temperature settings to reduce scald hazards.
Valves for reducing the point-of-use temperature by mixing cold and
hot water are available, see Figure 2. Also available are inexpensive
devices that attach to faucets to limit hot water temperatures. Contact
a licensed plumber or the local plumbing authority.
HOT WATER CAN SCALD: Water heaters are intended to produce hot
water. Water heated to a temperature which will satisfy space heating,
clothes washing, dish washing, and other sanitizing needs can scald
and permanently injure you upon contact. Some people are more likely
to be permanently injured by hot water than others. These include the
elderly, children, the infirm, or physically/mentally handicapped. If anyone
using hot water from this heater fits into one of these groups or if there
is a local code or state law requiring a certain temperature water at the
hot water tap, then you must take special precautions. In addition to
using the lowest possible temperature setting that satisfies your hot water
needs, a means such as a mixing valve, shall be used at the hot water
taps used by these people or at the water heater. Mixing valves are
available at plumbing supply or hardware stores, see Figure 2. Follow
manufacturer’s instructions for installation of the valves. Before changing
the factory setting on the thermostat, read the “Temperature Regulation”
section in this manual, see Figure 26.
Never allow small children to use a hot water tap, or to draw their
own bath water. Never leave a child or handicapped person
unattended in a bathtub or shower.
The water heater should be located in an area where the general
public does not have access. If a suitable area is not available, a
cover should be installed over the thermostat to prevent tampering.
The water temperature setting was factory set at the lowest temperature;
Pressing the “COOLER”
button decreases temperature and
TEMPERATURE REGULATION
pressing the “HOTTER” button increases the temperature.
Setting the water heater temperature at 120°F (49°C) (Approx. “
”
mark on temperature setting of gas valve) will reduce the risks of
scalds. Some states or local codes require settings at specific lower
temperatures.
To avoid any unintentional changes in water temperature settings,
the control has a tamper resistant feature for changing the temperature
setting. To change the temperature setting follow these instructions:
1. “Wake Up” the temperature indicators by holding down both
“COOLER” and “HOTTER” temperature adjustment buttons at the
same time for one second, see Figure 26. One or two of the
temperature indicators will light up. These indicators will only
remain on for 30 seconds if no further buttons are pressed. After
30 seconds the control will go back to “Sleep” mode.
2. Release both of the temperature adjustment buttons.
a. To decrease the temperature press and release the “COOLER”
button until the desired setting is reached.
b.To increase the temperature press and release the “HOTTER”
button until the desired setting is reached.
NOTE: Holding down the button will not continue to lower or raise
the temperature setting. The button must be pressed and released
for each temperature change desired.
Should overheating occur or the gas supply fail to shut off, turn off
the manual gas control valve to the appliance.
FIGURE 26.
TEMPERATURE INDICATORS
TEMPERATURE ADJUSTMENT BUTTONS
F = approx. 180°F (82°C) Nearly Instantaneous
E = approx. 170°F (77°C) Nearly Instantaneous
D = approx. 160°F (71°C) About 1/2 Second
C = approx. 150°F (65°C) About 1 1/2 Seconds
B = approx. 140°F (60°C) Less than 5 Seconds
B = approx. 130°F (54°C) More than 30 Seconds
= approx. 120°F (49°C) More than 5 Minutes
Time to Produce
2nd & 3rd Degree
Temperature Setting Burns on Adult Skin
Display
B C D E F