Filter
Top Products
Installation
Instructions
Certified to comply with ASME A112.18.1M
U.S. Patent No. 5,819,789
Roughing-in Dimensions
DRAIN INSTALLATION
Replace UPPER GASKET (7) and FRICTION RING (10).
Position the side threaded outlet rearward and secure by
tightening MOUNTING NUT (9). Thread ESCUTCHEON (5)
onto TRANSFER VALVE (8) until it seats against the
BIDET LEDGE.
STOPPER
Thread LOCKNUT (6), WASHER (7) and
GASKET (8) onto DRAIN BODY (5).
Apply a bead of PUTTY to underside
of FLANGE (9).
Feed DRAIN BODY (5) up through BIDET
and thread FLANGE (9) fully onto
BODY (5).
Tighten LOCKNUT (6) firmly, keeping the
PIVOT ROD (3) pointed towards the back
of the BIDET.
Place STOPPER into drain and assemble
O-RING (1), WASHER (2), PIVOT ROD (3)
and NUT (4) to DRAIN BODY (5). Concave
side of cup WASHER (2) is toward ball.
Push DRAIN ESCUTCHEON (10) onto
TAILPIECE (11).
BIDET
PUTTY
CLIP
4
9
3
1
4
11
6
5
8
7
2
10
2555.400
10
BIDET FITTING
.3&7
TOWN SQUARE
*Wrench
*Supplied with Fitting
*Hex key
Flat Blade Screwdriver
Adjustable Wrench
Channel Locks
Phillips Screwdriver
Required Tools
5VCJOH$VUUFS
Turn off hot and cold water
supplies before beginning.
CAUTION
BIDET FAUCET INSTALLATION
Assemble MOUNTING NUTS with RUBBER WASHERS (1)
onto the VALVE BODIES (2) and insert VALVE BODIES (2)
through outside holes, from underside of the BIDET
LEDGE. Drop the RUBBER RING (3) over the VALVE
BODIES (2) and screw on the ESCUTCHEON (4) until it
locks against the internal stop.
Tighten the MOUNTING NUT (1) to secure the
VALVE BODY (2).
Remove ESCUTCHEON (5), FRICTION RING (10) and
UPPER GASKET (7) from TRANSFER VALVE (8) and
insert into the center forward hole of BIDET.
COLD
HOT
BIDET
LEDGE
3
2
7
8
1
9
5
BIDET OUTLINE
IS SYMBOLIC
FINISHED
WALL
1-1/4 O.D. TAILPIECE
DOUCHE
SPRAY
2-1/8
DIA.
ADJ. 1-1/4
TO 2-1/4
3-7/8
5-1/2
1-3/8
DIA.
7/8 DIA.
TRANSFER VALVE
(FOR FLUSHING
RIM OR SPRAY)
FINISHED
FLOOR
DIVERTER
ASSEMBLY
1-1/4 MAX.
1-3/16 DIA.
(C)
(H)
4-1/4
FOR GROUND JOINT
CONNECTION OR 1/2 "
O.D. SLIP (INLETS)
REAR VIEW WITH
WALL REMOVED
8 TO 12
2-1/4
DIA.
Congratulations on purchasing your American Standard faucet
with EverClean nish found only on American Standard faucets.
To ensure that your installation proceeds smoothly-please read these instructions carefully before you begin.
with EverClean™ Finish
EverClean Finish
• One wipe eortlessly removes spots
• Eliminates the need for cleaners and scrubbing
• Permanent surface protectant remains beautiful
for the life of the faucet
• EverClean™ available on: Polished Chrome, Satin Nickel,
Stainless Steel, Polished Brass (or any combination of these nishes)