A SERVICE OF

logo

Open as PDF
next previous
English English
4 © Titan Tool Inc. All rights reserved.
Table of Contents
Safety Precautions ........................................................................... 2
General Description ........................................................................ 4
Setup ................................................................................................ 4
Operation ......................................................................................... 5
Preparing a New Sprayer ...........................................................................5
Preparing to Paint.........................................................................................5
Priming ............................................................................................................. 5
Painting ............................................................................................ 6
Painting in MultiFinish Mode ...................................................................6
Painting in Airless Mode ............................................................................6
Control Panel Indicators .............................................................................6
Pressure Relief Procedure .......................................................................... 7
Spraying Technique ........................................................................ 7
Cleanup ............................................................................................ 7
Maintenance .................................................................................... 8
General Repair and Service Notes ..........................................................8
Replacing the Motor .................................................................................... 9
Replacing the Gears ..................................................................................... 9
Replacing the Transducer ........................................................................10
Replacing the PRIME/SPRAY Valve .......................................................10
Servicing the Fluid Section ......................................................................11
Replacing the Filters ..................................................................................12
Troubleshooting ............................................................................ 12
Parts Listings .................................................................................. 38
Product Registration ..................................................................................47
Warranty ........................................................................................ 48
General Description
This MultiFinish spray system is versatile enough to use for low
pressure ne nish work as well as high pressure airless spraying. The
system includes a piston pump sprayer and an air compressor that
work together to provide this versatility.
Sprayer ON/
OFF switch
Pressure
control knob
Oiler cap
Oiler button
PRIME/
SPRAY knob
Compressor
ON/OFF switch
Air hose
outlet
Air gauge
Air pressure
regulator
Compressor
Ma
terial hose
outlet
Pusher stem
Return tube
Siphon tube
Setup
Perform the following procedure before plugging in the power cord
of an electric unit.
1. Make sure the pump ON/OFF switch and the compressor ON/
OFF switch are in the OFF position.
2. Make sure the pressure control knob is in its OFF position in
the white zone.
3. Lock the gun by ipping the trigger lock into lock position
(see spray gun manual).
4. Using a wrench, attach a minimum of 50’ of 1/4” nylon airless
spray hose to the material outlet tting on the pump. Tighten
securely.
5. Attach the spray hose to the material inlet tting on the spray
gun. Using two wrenches (one on the gun and one on the
hose), tighten securely.
Ma
terial
Inlet
Fitting
Air Inlet
Fitting
Coupling
Air Hose
Material
Hose
Standard Hose
Co
nguration:
Ma
terial
Inlet
Fitting
Air Inlet
Fitting
With Optional
Whip Hoses:
Coupling
Air Whip
Hose
Air Hose
Material Hose
Material
Whip Hose
Straps
Make sure all airless hoses and spray guns are
electrically grounded and rated for at least 2800 PSI
(19 MPa) fluid pressure.
6. Attach the air hose to the air outlet tting on the compressor.
Tighten securely.
7. Attach the air hose coupling to the air inlet tting on the spray
gun. Attach the air hose to the coupling. Tighten securely.
Reversing the hose connections could result in serious
injury. Make sure the airless spray hose is connected
from the diaphragm pump to the material inlet fitting
on the gun and the air hose is connected from the
compressor to the air inlet fitting on the gun.
8. Ensure that the siphon tube and the return hose are attached
and secure.
9. Remove the ll cap with a straight-slot screwdriver, or a coin.
Fill the oil reservoir with one ounce of piston seal lubricant
(P/N 313-481). Replace oiler cap.
10. Press oiler button 2-5 times to prime the oiler. Press once for
every eight hours of usage to lubricate the uid section.
IMPORTANT: Never operate unit for more than ten seconds
without fluid. Operating this unit without fluid will cause
unnecessary wear to the packings.
11. Fully depress the pusher stem to make sure the inlet ball is
free.
12. Make sure the electrical service is 120V, 15 amp minimum.
13. Plug the power cord into a properly grounded outlet at least
25’ from the spray area.
IMPORTANT: Always use a minimum 12 gauge, three-wire
extension cord with a grounded plug. Never remove the third
prong or use an adapter.