Parameter Guide
47
3 Use the [+/YES] [–/NO] keys to select the copy source
program.
4 Use CURSOR[®] to move the cursor to the copy
source timbre.
5 Use the [+/YES] [–/NO] keys to select the copy source
timbre.
If the copy source program is Single, it will not be possi-
ble to select the copy source timbre (only timbre 1 is
available).
6 Use the CURSOR [®] key to move the cursor to “OK,”
and press the [+/YES] key.
You will be asked to confirm the copy function.
7 Press the [+/YES] key once again.
The copy operation will be completed, and the display
will indicate “Completed.”
8 Press the [EXIT] key.
You will return to the first screen of the “CopyTimbre”
function.
D: SwapTimbre
This function swaps (exchanges) the settings of timbres 1
and 2 in the currently selected program.
The swap function cannot be performed for Single pro-
grams.
Procedure
1 In LCD Edit mode press the SELECT [16] key, and then
press the CURSOR [®] key three times.
The LCD screen will show Page 26D: UTILITY “Swap-
Timbre.”
2 Press the [+/YES] key.
You will be asked to confirm the swap function.
3 Press the [+/YES] key once again.
The timbres will be swapped, and the display will indi-
cate “Completed.”
4 Press the [EXIT] key
You will return to the first screen of the “SwapTimbre”
function.
E: InitSeq
This function initializes one or all sequences of the currently
selected timbre.
InitSeq...................................................... [SEQ1...ALL]
Select the sequence(s) that you wish to initialize.
When you initialize a sequence, the data recorded in that
sequence will be erased.
Procedure
1 In LCD Edit mode press the SELECT [16] key, and then
press the CURSOR [®] key four times.
The LCD screen will show Page 26E: UTILITY “InitSeq.”
2 Press the [+/YES] key.
The LCD screen will show the sequence to be initialized
(InitSeq).
3 Use the [+/YES] [–/NO] keys to select the sequence that
you wish to initialize.
If you select ALL, all sequences (SEQ 1–3) of the timbre
will be initialized.
4 Use CURSOR [®] to move the cursor to “OK,” and
press the [+/YES] key.
You will be asked to confirm the initialize function.
5 Press the [+/YES] key once again.
The sequence(s) will be initialized, and the display will
indicate “Completed.”
6 Press the [EXIT] key.
You will return to the first screen of the “InitSeq” func-
tion.
F: CopySeq
This function copies sequence data from another timbre to
the currently selected timbre.
Source Program......................................... [A01...H16]
Select the copy source program.
Source Timbre .....................................................[1, 2]
Select the copy source timbre.
Source Seq..................................................... [S1...S3]
Select the copy source sequence.
Destination Seq ..................................................[1...3]
Select the copy destination sequence.
Procedure
1 In LCD Edit mode, press the SELECT [16] key and then
press the CURSOR [®] key five times.
The LCD screen will show Page 26F: UTILITY “Copy-
Seq.”
2 Press the [+/YES] key.
The LCD screen will indicate the copy source program
(Source Program), timbre (Source Timbre), sequence
(Source Seq), and copy destination sequence (Destina-
tion Seq).
26C UTILITY
Are You Sure OK?
26D UTILITY
SwapTimbre OK?
26D UTILITY
Are You Sure OK?
26E UTILITY
Are You Sure OK?
26F UTILITY
A01 T:1 S1”1 OK?
Source Program
Source Timbre Source Seq
Destination Seq
Program parameters
