Part No. 890424 Form No. F011398A
Page 12 of 12
Engine Service and Warranty
Contact your nearest engine manufacturer's autho-
rized servicing dealer.
22.122.1
22.122.1
22.1
2222
2222
22
BILLY GOAT INDUSTRIES INC.
P.O. BOX 308 (1803 S JEFFERSON) LEE'S SUMMIT, MO 64063 / USA
PHONE: 816-524-9666 FAX: 816-524-6983
R
WARRANTY PROCEDURE
Please fill in the WARRANTY CARD and send the upper part to Billy Goat.
The WARRANTY terms are stated on the lower part which remains with the
user. Whenever a Billy Goat Machine is faulty due to a defect in material
and / or workmanship, the owner should make a warranty claim as follows:
The Machine should be taken to the dealer from whom it was
purchased or to an authorized Billy Goat dealer.
The owner should present the remaining half of the Warranty
Registration Card, or, if this is not available, the invoice or receipt.
The Warranty Claim will be filled in by the authorized Billy Goat Dealer,
who will send it with the faulty part to Billy Goat headquarters.
The Quality / Service department at Billy Goat headquarters will study
the claim and parts and will notify their conclusions.
The decision by the Quality / Service department at Billy Goat
headquarters to approve or reject a Warranty claim is final and
binding.
Note:
To process a Warranty Claim, it is necessary to quote the Model
& Serial number who are printed on the Billy Goat Serial Plate.
Purchased
from
Purchase
Date
2121
2121
21
Serial Plate
Record your machine model, serial number
and date-of-purchase and where purchased
R
min
-1
Operator
1803 S. Jefferson
P.O. Box 308
Lee's Summit,
MO 64063 / USA
Tel (816) 524-9666
Fax (816) 524-6983
Model Serial No.
Unit(Weight) Engine Power
lbs. kg kW rpm
L
A
p
109
97
L
A
Engine stalls or labors when
chipping.
Feeding branches into chipper too rapidly. Engine service may be
required.
Feed branches at a slower rate. Service engine.
Poor chipping performance.
Extremely hard wood. Dull or damaged chipper blade.
Avoid extremely hard wood. Sharpen or replace chipper blade (see
page 8).
Will not vacuum or has poor
vacuum performance.
Clean debris bag. Shake bag clean or wash. Adjust nozzle height.
Check for hose kit cap. Unclog nozzle or exhaust (see page 5).
Allow air to feed with debris.
Solution
Problem Possible Cause
TROUBLESHOOTING
Before Requesting Service Review These Suggestions
Engine will not start. Check stop switches, throttle, and gasoline. Connect spark plug wire.
Clean or replace air cleaner. Or contact a qualified service person.
Self propelled drive will not
release.
Clutch cable out of adjustment. Clutch not lubricated and is locked-
up.
Adjust clutch cable. See page 9 Clutch Adjustment. Oil clutch.
No self propelling.
Operator's bail not releasing clutch. Broken or out of adjustment
clutch cable. Worn or broken clutch assembly. Bracket control
assembly (item 112) out of adjustment.
Adjust clutch cable. Adjust bracket control assembly. Replace any
worn or damaged or malfunctioning parts.
Throttle in off position. Out of gasoline. Bad or old gasoline.
Spark Plug wire disconnected. Dirty air cleaner.
Abnormal vibration.
Loose or out of balance impeller or loose engine.
Check impeller and replace if required. Check Engine.
Engine is locked, will not
pull over.
Debris locked in chipper blade, hopper or inside impeller. Engine
problem.
See page 5, Clearing a clogged chipper hopper. Contact an engine
servicing dealer for engine problems.
Dirty debris bag. Nozzle height set too high or too low. Hose kit cap
missing. Clogged nozzle or exhaust. Excessive quantity of debris.
20
19
( Continued from
page 11 )
PARTS LIST
Item
No. Description
KD510SP Part
No. Qt
.
TKD510SP Part
No. Qt
.
86 Wheel With
procket Ass'
ast
21, 94, 95, 96
890242 2 890242 2
87
hain 52 Pitch 890239 2 890239 2
88
hain 40 Pitch 900323 1 900323 1
89 Washer Flat 5
16
3
8 ID x 7
8 x 1 1
6
*8171003 4 *8171003 4
90 Bolt
arria
e 5
16 - 18 x 3
4 *8024039 4 *8024039 4
91 Washer
prin
Lock 5
16 *8177011 4 *8177011 4
92 Nut Re
ular 5
16 - 18 *8142002 4 *8142002 4
93 Jacksha
t 900320 1 900320 1
94
procket
per Assemb
size # 65A26
26 Teeth 890238 1 890238 1
95
crew
el
Tap 1
4-14 x 3
4
Per Assembl
800505 5 800505 5
96 Washer Lock External Tooth
Per Assembl
*8181007 5 *8181007 5
97 Jacksha
t Ass'
incl. 93, 101, 102, 107, 108, 109
890197 1 890197 1
98
hield Mu
ler TKD
P 890190 1 890190 1
99 Label
lutch 830503 1 830503 1
100 Label - Warnin
uards 900327 1 900327 1
101 Bearin
Plate 900317 2 900317 2
102 Bearin
Ball
with
nap Rin
900321 2 900321 2
103
104 Rod Bail
lutch 900970 1 900970 1
105
106
107
procket - 17 Tooth 900303 1 900303 1
108
procket - 8 Tooth 900302 2 900302 2
109 Roll Pin 3
16 Dia. x 1 1
4 L
. *8195166 4 *8195166 4
110 Locknut 5
16 - 18 Flan
e 850164 5 850164 5
111
112 Bracket
ontrol Ass'
incl. 113, 114, 115
900221 1 900221 1
113
prin
900136 1 900136 1
114 Roll Pin 1
8" Dia. x 1 1
4 L
. *9195106 1 *9195106 1
115 Rod
lutch 900208 1 900208 1
116
crew
ap 1
4-20 x 1" L
. *8041006 2 *8041006 2
117 Washer 1
4" Flat
5
16 ID x 3
4
d x 1
16
*8171002 4 *8171002 4
118
uard
hain Ass'
TKD
P 890231 1 890195 1
119
lip -
lutch
able 900999 1 900999 1
120
121
lutch Double Release 900307 1 900307 1
122
123 Label Read Owner's Manual 890301 1 890301 1
