Filter
Top Products
8
The programmable thermostats are programmed with the
energy saving settings shown in the table below for all days
of the week. If this program suits your needs, simply set the
thermostat clock and press the RUN Sched button.
The table below shows the factory set heating and cooling
schedule for all days of the week.
Wake Up
(Period 1)
Leave For Work
(Period 2)
Return Home
(Period 3)
Go To Bed
(Period 4)
Heating
Program
6:00 AM 70°F 8:00 AM 62°F 5:00 PM 70°F 10:00 PM 62°F
Cooling
Program
6:00 AM 75°F 8:00 AM 83°F 5:00 PM 75°F 10:00 PM 78°F
Planning Your Program – Important
The Heating and Cooling Program schedules below allow you
to pencil in your own program times and temperatures.
The programmable comes confi gured for 5/1/1 day program-
ming and can also be confi gured for 5/2 day programming
(see confi guration section).
Factory settings are listed on Monday through Friday, Satur-
day and Sunday. If you are re-programming a 5/2 day sched-
ule, pencil in your own times and temperatures directly below
the factory times and temperatures.
If you are re-programming a 5+1+1 fi ll in all lines with the
times and temperatures you want.
Keep the following guidelines in mind when planning your
program.
• In Heating, lower temperatures will save energy.
• In Cooling, higher temperatures will save energy.
• If you plan on using Auto Changeover, do not program
the heating higher than the cooling.
Worksheet for Re-Programming 5/2 Day and 5+1+1 Day Program
Heating
Program
Wake Up
(Period 1)
Leave For Work
(Period 2)
Return Home
(Period 3)
Go To Bed
(Period 4)
Mo-Fri
6:00 AM 70°F 8:00 AM 62°F 5:00 PM 70°F 10:00 PM 62°F
Sat-Sun
or Sat
6:00 AM 70°F 8:00 AM 62°F 5:00 PM 70°F 10:00 PM 62°F
Sun
5+1+1 only
6:00 AM 70°F 8:00 AM 62°F 5:00 PM 70°F 10:00 PM 62°F
Cooling
Program
Wake Up
(Period 1)
Leave For Work
(Period 2)
Return Home
(Period 3)
Go To Bed
(Period 4)
Mo-Fri
6:00 AM 75°F 8:00 AM 83°F 5:00 PM 75°F 10:00 PM 78°F
Sat-Sun
or Sat
6:00 AM 75°F 8:00 AM 83°F 5:00 PM 75°F 10:00 PM 78°F
Sun
5+1+1 only
6:00 AM 75°F 8:00 AM 83°F 5:00 PM 75°F 10:00 PM 78°F
Energy Saving ENERGY STAR
®
Factory Pre-Program
PROGRAMMING (For Programmable Model Only)
Enter the Heating Program
1) Press SYSTEM button to select “Heat” in the system
switch area indicating the active mode being pro-
grammed.
2) Press the Menu button and then press Schedule.
3) The top of the display will show the day(s) being pro-
grammed. The time and temperature (fl ashing) are also
displayed. “1” will also be displayed to indicate the pe-
riod.
4) Press
or button to change the temperature to
your selected temperature for the 1st heating period.
5) Press Time button, time will fl ash.
6) Press
or button to adjust the start time for the
1st period.
7) The time will change in 15 minute increments.
8) After you have set the time and the temperature for
the period to begin, press Schedule to advance to the
next program period.
9) Repeat steps 2 through 8 until all of the program times
and temperatures are set for all program periods on
that day.
10) Press Schedule to the next day and repeat steps 2
through 9.
11) When programming is complete and all of the times and
temperatures match your desired heating schedule, press
Run Schedule. The thermostat will now run your pro-
gram.
Enter the Cooling Program
1) Press SYSTEM button to select “Cool” in the system
switch area indicating the active mode being pro-
grammed.
2) Follow Enter Heating Program instructions for entering
cooling times and temperatures.