Filter
Top Products
900 SERIES ROLLING SERVICE DOORS
1
900 SERIES
ROLLING SERVICE DOORS
GENERAL SPECIFICATIONS
FOR ROLLING SERVICE
DOORS
Note to Specifiers:
Words in parentheses indicate
frequently specified and highly
recommended options.
PART 1 GENERAL
1.01 Work Included—The opening
will be equipped with Wayne-
Dalton 900 Series rolling doors,
Model _____ as
manufactured by Wayne-Dalton
Corp.
1.02 Related Work—Opening
preparation, miscellaneous or
structural metal work, access
panels, finish or field painting, field
electrical wiring, wire, conduit,
fuses, and disconnect switches are
in the Scope of Work of other
divisions or trades.
PART 2 PRODUCT
2.01 Curtain will be composed of
prime painted galvanized steel
interlocking slats (A) gauge, No.
(B) slats, roll-formed from (C)
per ASTM standards and designed
to withstand a 20 PSF windload.
Ends of alternate slats will be fitted
with metal endlocks/windlocks.
Bottom Bar will consist of 2 equal
galvanized steel (stainless
steel) angles, (aluminum
extrusion) minimum
1
¼
8
" thick, to
stiffen curtain with neoprene loop
astragal. When required for
additional security, provide (slide
bolts) (cylinder locks) on the
bottom bar operable from (coil
side) (opposite coil side)
(both sides).
2.02 Guides will be of roll-formed
galvanized steel channels and
angles (three angle assembly)
of steel (stainless steel)
(aluminum) to form a slot of
sufficient depth to retain curtains in
guides to resist 20 PSF windload.
Guides may be provided with
integral windlock bars and
removable bottom bar stops.
2.03 Brackets will be of galvanized
steel plates with permanently
sealed ball bearings. Designed to
enclose ends of coil and provide
support for counterbalance pipe at
each end.
2.04 Counterbalance: Curtain to
be coiled on a pipe of sufficient
size to carry door load with
deflection not to exceed .03 inches
per foot of door span and to be
evenly balanced by helical springs,
oil tempered torsion type designed
with a 25% safety factor. Cast iron
barrel plugs will be used to anchor
springs to tension shaft and pipe.
2.05 Hood will be minimum 24
gauge (prime painted
galvanized) (galvanized)
(slatted) steel, flanged at top for
attachment to header and flanged
at bottom to provide longitudinal
stiffness. Hood will enclose curtain
coil and counterbalance
mechanism.
2.06 Finish: Shop coat of rust
inhibitive primer on non-galvanized
surfaces and operating
mechanisms. Aluminum finish to
be (mill) (204R1 clear
anodized) (bronze anodized).
Stainless steel finish to be (#4).
Curtain will be (white) (blue)
(gray) (tan) (brown).
2.07 Operation: Door will be
operated by means of (manual,
push-up) (chain hoist with gear
drive reduction) (awning
crank) (wall crank box)
(motor operation). (Electrical)
(Pneumatic) sensing edge to be
attached to bottom bar to (stop)
(stop and reverse) the door
when it contacts an object during
the closing cycle.
2.08 Weatherstripping: Air-
Bar/Extr-Tite doors will include flat
slats, bottom astragal, exterior
surface guide weatherstrip, and
internal hood baffle weatherstrip.
2.09 Locking: (Manual push-up
doors will have interior slide-bolts
suitable for padlocks by others.)
(Chain-hoist door will have chain
keepers suitable for padlocks by
others.) (Electric-motor
operation doors will lock through
the operator gearing.) (Cylinder
locks can be provided with the
doors.)
CAUTION: When specifying
cylinder locks on electric-motor
operated doors, electric interlocks
should also be specified to prevent
operation when lock bolts are
engaged in the guides, thus
preventing damage to the curtain
and/or operator.
PART 3 EXECUTION
3.01 Install the doors in
accordance with Wayne-Dalton
Corp. instructions and standards.
Installation and maintenance will
be by an authorized Wayne-Dalton
representative.
Because of continuing product improvements, we reserve the
right to change the product specifications and designs without
prior notice.
WAYNE-DALTON CORP. • ONE DOORDRIVE • MT. HOPE, OH 44660 • PH. 800-764-1457 • FX. 800-336-
1422
For easier door specifications or product questions call the WayneTec Consulting Service 1-800-764-1457.
COLORS INCLUDE:
(22 and 24 gauge
only)
White
Blue
Gray
Tan
Brown
©2001 Wayne-Dalton Corp. Rev. 11/01 246570