Filter
Top Products
Wall
A
Closet
Flange
C
/
L
Floor
4 holes
Anchor
2"
9"
Wall
"RI"
Closet
Flange
C
/
L
Supply
Valve
STEP 1 Piping Check and Roughing-in
In order for your new TOTO toilet to fit correctly, check the
dimensions below.
a) Distance
between
finished wall
to the center
of the toilet
outlet, Rough-In (“RI”):
Please make sure that you have the correct outlet connection part.
b) Water supply must be approx. 8 in. or 10 in. to the left
(facing bowl) from center line of closet flange and approxi-
mately 4-1/2 in. above the floor.
Removing Exhisting Toilet (If Necessary)
Turn off water supply. Flush the toilet, remove any remaining
water from tank and bowl.
Disconnect water connector. Remove tank and bowl. Remove
old wax seal and mounting bolts.
STEP 2 Installing Mounting Bolts
Clean any debris out of the closet flange, then
install the mounting bolts into the slots of the
flange. The bolt should be inserted into the
slot with its head down and threaded
shank pointed upward.
STEP 3 Installing Outlet Connection
Drill 4 holes 11/64” on the floor
at location shown. (1/4” holes
are for tile/concrete floor
using anchors.)
Turn the PVC outlet connection upside down. Firmly press a
new wax seal onto the circular recess around the outlet opening.
Turn the outlet connection upright and lower it into position
over closet flange. With the unit properly
aligned, press down firmly to set
wax seal.
CAUTION: DO NOT move
the outlet connection after
the wax seal is set.
Insert washers
and thread
nuts onto
mounting bolts
and hand tighten.
Then tighten bolts
an additional
1/2 turn.
Secure back side
of outlet connec-
tion to the floor using
the 4 screws and
washers.
Insert the T-Bolts into the slots with its
head down and threaded shank pointed upward.
NOTE: Do not remove the white tie-wrap from rubber sleeve.
Level the PVC outlet.Do not use excessive force.
STEP 4 Installing Toilet
Lift the toilet and gently lower it into position over closet
flange. Make sure that the spigot outlet of toilet slips into
rubber sleeve and T-Bolts fit through the openings in the
base of toilet.
NOTE: A petroleum lubricant can be used on the rubber
sleeve to lubricate the spigot outlet for an easier installation.
Insert washer and thread nuts on to bolts and hand tighten.
Then tighten bolts an additional 1/2 turn. Install cover plates.
“RI”
12 inch
10 inch
14 inch
TSU01W.12
(supplied)
TSU01W.10
(optional - must be purchased separately)
TSU01W.14
(optional - must be purchased separately)
Outlet Connection Part No.
9-1/2"
7-1/2"
11-1/2"11-1/2"
RI A Dimension
10” A = 3-1/2”
12” A = 5-1/2”
14” A = 7-1/2”
T-Bolts
nut
washer
slot
rubber
sleeve
Wax seal
WARNING: DO NOT over tighten the nuts, damage to
china or plastic parts may result.
FIVE YEAR LIMITED WARRANTY
Warranty applies to select Augusta Products only.
1. TOTO warrants its vitreous china products to be free from manufac-
turing defects under normal use and service for a period of five (5)
years from date of purchase. This warranty is extended only to the
ORIGINAL PURCHASE.
2. TOTO’s obligation under this warranty are limited to repair or
replacement at TOTO’s option, of products or parts found to be defec-
tive, provided that such products were properly installed and used in
accordance with instructions. TOTO reserves the right to make such
inspections as may be necessary in order to determine the cause of the
defect. TOTO will not charge for labor or parts in connection with war-
ranty repairs or replacements. TOTO is not responsible for the cost or
removal, return and/or reinstallation of products.
This warranty does not apply to the following items.
a. Damage or loss sustained in a natural calamity such as fire,
earthquake, flood, thunder, electrical storms, etc.
b. Damage or loss resulting from any unreasonable use, misuse,
abuse, negligence, or improper maintenance of the product.
c. Damage or loss resulting from removal, improper repair, or
modification of the product.
d. Damage or loss resulting from sediments or foreign matter
contained in water system.
e. Damage or loss resulting from improper installation or from
installation of a unit in a harsh and/or hazardous environment.
f. Tank flushing mechanisms of plastic or rubber moving parts.
g. Toilet seats of plastic, wood or metal.
4.This warranty gives you specific legal rights. You may have other
rights which vary from state to state.
5. To obtain warranty repair service under this warranty, you must take
the product or deliver it prepaid to a TOTO service facility together with
a letter starting the problem, or contract a TOTO distributor or products
service contractor, or write directly to TOTO KIKI U.S.A. INC, 1155
Southern Road, Morrow, GA 30260 (888) 295-8134. If because of the
size of the product or nature of the defect, the product cannot not be
returned to TOTO, receipt by TOTO of written notice of the defect shall
constitute delivery. In such case, TOTO may choose to repair the prod-
uct at the purchaser’s location or to pay to transport the product to a
service facility.
This written warranty is the only warranty made by TOTO. Repair or
replacement as provided under this warranty shall be the exclusive rem-
edy available to the purchaser. TOTO shall not be responsible for lost of
the product or for other incidental, special or consequential damages or
expenses insured by the purchaser, or for labor or other costs due to
installation or removal, or costs of repairs by others, or for any other
expenses not specifically stated above. Except to the extent prohibited
by applicable law, any implied warranties, including that of mer-
chantability or fitness for use, are expressly limited to the duration of
this warranty. Some states do not allow limitations on how long an
implied warranty lasts or the exclusion or limitation of incidental or con-
sequential damages, so the above limitation and exclusion may not apply
to you.
WARNING! TOTO shall not be responsible or liable for any failure of,
or damage to, this product or product component caused by either chlo-
ramines in the treatment of public water supply or in tank bowl cleaners
containing chlorine (calcium hypochlorite). Note: The use of high con-
centration of chlorine or chlorine related products can seriously damage
the fittings. This damage can cause leakage and serious property dam-
age. For more information, please call us at (888) 295-8134.
STEP 5 Connecting Water Line
Supply stop should be installed per supply stop instructions
at location shown in Step 1.
Flush water line briefly to
ensure removal of debris.
Connect provided flexible
supply to supply stop.
CAUTION: DO NOT
OVER-TIGHTEN NUT.
Open supply stop, check
for leakage. Slightly
retighten if necessary.
Water Supply
Pressure should be:
20 to 80 psi Static
STEP 6 Operation
NO BALLCOCK/FILL VALVE ADJUSTMENT NEEDED.
Water will automatically stop at proper level.
Flush toilet several times. Check flapper valve for proper
operation. Make sure that chain is not tangled and flapper
arm is in its proper position.
STEP 7
Install toilet tank lid.
STEP 8
Install toilet seat. (Top Mount Bolt Set is included in the bowl).
Insert rubber bushing nuts into bowl seat holes.
Note: Remove existing seat if necessary.
Place seat on bowl and rotate the hinge unit into place while
holding seat down on bowl.
Fasten and tighten bolt from top with screwdriver. Replace
bolt cap and lower lid (if necessary).
Water Inlet
Washer
Coupling Nut
Trim Plate
Nipple
Valve
Compression
Valve Nut
Flexible Supply
Tank
Seat Bolt
Rubber
Bushing Net
spigot outlet
rubber
sleeve
nut
washer
Cover
Plate
REPLACEMENT PARTS
Model Flapper Fill Valve Flush Valve Trip Lever
MS904114 THU092-5 TSU06A.4 THU014 THU015#XX
MS884114 THU092-1 TSU04A.5 THU001N THU004#XX
MS874114S THU092-3 TSU05A.11 THU013 THU004#XX
MS914114THU092-8 TSU04A.5 THU128 THU099#XX