Filter
Top Products
5
1 OPERATION (Green)
2 TIMER (Orange)
3 PRE.DEF (Preheat/Defrost/Self Cleaning) (Orange)
4 TEMPORARY button
Loading Batteries
1. Remove the slide cover.
2. Insert 2 new batteries (AAA type) following the (+) and
(–) positions.
Clock Setup
1. Push by tip of the pencil.
If timer indication is flashing, go to the next step 2.
2. Press or : Adjust
the time.
3. Press : Set the time.
Remote Control Reset
Push by tip of the pencil or
1. Remove the batteries.
2. Press .
3. Insert the batteries.
Start/Stop
1. Press to start
operation.
(A receiving beep is heard)
2. Press to stop
operation.
(A receiving beep is heard)
1 Infrared signal emitter
2 Start/Stop button
3 Mode select button (MODE)
4 Temperature button (TEMP)
5 Fan speed button (FAN)
6 On timer button (ON)
7 Off timer button (OFF)
8 Setup button (SET)
9 Clear button (CLR)
0 Memory and Preset button (PRESET)
! One-Touch button (ONE-TOUCH)
@ High power button (Hi-POWER)
# Economy button (ECO)
$ Quiet button (QUIET)
% Comfort sleep button (COMFORT SLEEP)
^ Set clock button (CLOCK)
& Check button (CHECK)
* Reset button (RESET)
Note:
When pushing the “SWING”, “FIX” and
“FILTER” buttons, indoor unit does not
operate and the receiving beep sound also not appear.
Press the “ONE-TOUCH” button for fully automated operation that is customized to the
typical consumer preferences in your region of the world.
The customized settings control temperature, air flow strength and other settings to provide
you alternate contact with “ONE-TOUCH” of the button. If you prefer other settings you can
select from the many other operating functions of your Toshiba unit.
Press : Start the operation.
To automatically select cooling or heating operation
1. Press : Select A.
2.
Press : Set the desired temperature.
3. Press : Select AUTO, LOW , LOW+ , MED , MED+ , or
HIGH .
1. Press : Select Cool , or Heat .
2.
Press : Set the desired temperature.
3. Press : Select AUTO, LOW , LOW+ , MED , MED+ , or
HIGH .
For dehumidification, a moderate cooling performance is controlled automatically.
1. Press : Select Dry .
2.
Press : Set the desired temperature.
To automatically control room temperature and cooling (or heating) capacity for faster
cooling (or heating) operation. (except in DRY mode)
Press : Start and stop the operation.
To automatically control room to save energy (except in DRY mode)
Press : Start and stop the operation.
Note: Cooling operation; the set temperature will increase automatically 1 degree/hour for
2 hours (maximum 2 degrees increase).
For heating operation the set temperature will decrease.
In case of the misplaced or discharged remote
control
• Pressing the TEMPORARY button, the
unit can start or stop without using the
remote control.
• Operation mode is set on AUTOMATIC
operation, preset temperature is 24°C
and fan operation is automatic speed.
Set the timer when the air conditioner is operating.
Daily timer allows the user to set both the ON & OFF timers and will be activated on a
daily basis.
Setting Everyday Timer
• During the every day timer is activating, both arrows ( , ) are indicated.
Note:
• Keep the remote control in accessible transmission to the signal receiving unit;
otherwise, the time lag of up to 15 minutes will occur.
• The setting will be saved for the next same operation.
Set your preferred operation for future use. The setting will be memorized by the unit for
future operation.
1. Select your preferred operation.
2.
Press and hold for 3 seconds to memorize the setting. The
P
mark
displays.
3. Press : Operate the preset operation.
1
SIGNAL RECEIVING UNIT DISPLAY
2
PREPARATION BEFORE USE
8
m
o
r
l
e
s
s
3
REMOTE CONTROL
4
ONE-TOUCH
5
AUTOMATIC OPERATION
Setting the ON Timer Setting the OFF Timer
1
Press : Set the desired ON timer.
Press : Set the desired OFF timer.
2
Press : Set the timer. Press : Set the timer.
3
Press : Cancel the timer. Press : Cancel the timer.
1
Press : Set the ON timer.
3
Press .
2
Press : Set the OFF timer.
4
Press button during the
( or ) mark flashing.
6
COOLING / HEATING OPERATION
7
DRY OPERATION
8
Hi-POWER OPERATION
9
ECO OPERATION
10
TEMPORARY OPERATION
TEMPORARY button
11
TIMER OPERATION
12
PRESET OPERATION