Filter
Top Products
5
Therma-Tru
®
Light Commercial/Multi-Family - Standard Hardware Preps.
STEEL DEADBOLT PREP:
STAMPED 1 1/8" x 2 3/4" OPTIONAL
DEADBOLT PREP FOR STEEL FRAMES.
AVAILABLE WITH ADJUSTA-FIT,
ADJUSTA-TRIM, HOLLOW METAL,
SECURA-FIT & VISTA III FRAMES.
STEEL DEADBOLT PREP
STAMPED 1 1/18" x 2 3/4" OPTIONAL
DEADBOLT PREP FOR STEEL FRAMES.
AVAILABLE WITH ADJUSTA-FIT,
ADJUSTA-TRIM, & SECURA-FIT
FRAMES.
STAMPED TEE STRIKE PREP FOR
STEEL FRAMES. AVAILABLE w/
ADJUSTA-FIT, ADJUSTA-TRIM,
HOLLOW METAL & SECURA-FIT
STEEL TEE STRIKE PREP
STAMPED TEE STRIKE PREP FOR STEEL
FRAMES. AVAILABLE WITH ADJUSTA-
FIT, ADJUSTA-TRIM & SECURA-FIT
FRAMES.
STAMPED LIP STRIKE PREP FOR
STEEL FRAMES. AVAILABLE w/
ADJUSTA- FIT, ADJUSTA- TRIM,
SECURA-FIT&VISTAIIIFRAMES
STEEL LIP STRIKE PREP
STAMPED LIP STRIKE PREP FOR STEEL
FRAMES. AVAILABLE WITH ADJUSTA-
FIT, ADJUSTA-TRIM & SECURA-FIT
FRAMES.
STEEL 4 7/8" ANSI PREP
STAMPED 4 7/8" ANSI STRIKE PREP FOR
STEEL FRAMES. AVAILABLE w/
ADJUSTA-FIT, ADJUSTA-TRIM, HOLLOW
METAL&SECURA-FITFRAMES.
STAMPED 4 7/8" ANSI STRIKE PREP
FOR STEEL FRAMES. AVAILABLE
WITH ADJUSTA-FIT, ADJUSTA-TRIM &
SECURA-FIT FRAMES.
11/4"x8"MORTISELOCKPREP
451/4"FR
OMTOPOFDOOR
447/8"FR
OMTOPOFDOOR
51/2"ST
ANDARD
STANDARD 11/8"x 21/4" STRIKEw/
OPTIONAL11/8"x21/4"DEADBOLTPREP
*NOTE:MORTISELOCK
ISNOTOFFEREDWITH
LANDMARKDOORS.
LATCH PREPS
STANDARD 1 1/18" x 2 1/4"
STRIKE WITH OPTIONAL
1 1/18" x 2 1/4"DEADBOLT PREP.
1 1/4" x 8" MORTISE LOCK PREP.
NOTE: MORTISE LOCK IS NOT
OFFERED WITH LANDMARK
DOORS.
45 1/4" FROM TOP OF DOOR
44 7/8" FROM TOP OF DOOR
5 1/2" STANDARD
51/2"ST
ANDARD
447/8"FR
OMTOPOFDOOR
BENCHMARKSTEELENTRANCEDOOR.
DEADBOLTHOLE:DRILLED
THROUGHWOODBLOCK.
DEADBOLTFILLERPLATE
DEADBOLTASSEMBLY
KNOBLATCH
LATCHFILLERPLATE
STANDARD LATCH PREP
44 7/8" FROM TOP OF DOOR
KNOB LATCHLATCH FILLER PLATE
DEADBOLT ASSEMBLY
DEADBOLT FILLER PLATE
DEADBOLT HOLE: DRILLED
THROUGH WOOD BLOCK.
BENCHMARK STEEL ENTRANCE DOOR
5 1/2" STANDARD
Note Alldimensions
are typical on both
sides
:
4.080
1.062
.375
.500
1.500
2.500
3.500
3.985
2.040
.097(12 Ga.)
Drill.295 /.300 Dia.
Countersunkfor a
#10flat headscrew
5/8"Rad.
.018
4" x 4" HINGE DETAIL
.097 (12 GA.)
.018
5/8" RAD.
2.040
4.080
DRILL .295/.300 DIA.
COUNTERSUNK FOR A #10
FLAT HEAD SCREW.
NOTE: ALL DIMENSIONS ARE
TYPICAL ON BOTH SIDES.
1.062
.375
.500
1.500
2.500
3.500
3.985