Filter
Top Products
NOTE: DIAGRAMS & ILLUSTRATION NOT TO SCALE.
12
8. CAUTION: DO NOT OPERATE THIS APPLI-
ANCE WITH A BROKEN GLASS PANEL. Where
broken glass exists, the complete glass enclo-
sure panel must be replaced. See the Replace-
ment Parts List on page 18 for correct replace-
ment part numbers. Glass enclosure panel re-
moval and installation instructions are described
on pages 5 and 10 respectively.
Brass Square Surround Kit
Decorative brass square surround kits are avail-
able for use with these appliances. The BSK-5
and BSK-6 are designed to attach directly to the
front face of the appliance at its extreme edges.
The brass square surround kits provide a pic-
ture frame finish for the appliance 2 ¹⁄₂" wide.
Use the BSK-5 with CF5500 appliances and the
BSK-6 with CF6500 appliances. The brass
square surround kit can be retrofitted onto
previously installed appliances.
Brass Louver Kit
Decorative brass louvers are available for use
these appliances. These louvers are designed
to replace the standard black louvers that are
provided with the appliance. The brass louver
louver kit includes three (3) plated louvers and
a fourth (black) louver, that simply snap into
place. They provide a touch of elegance to the
CF appliance. This kit can be retrofitted to
previously installed appliances.
WARNING: CHILDREN AND ADULTS
SHOULD BE ALERTED TO THE HAZARDS
OF HIGH SURFACE TEMPERATURES. USE
CAUTION AROUND THE APPLIANCE TO
AVOID BURNS OR CLOTHING IGNITION.
YOUNG CHILDREN SHOULD BE SUPER-
VISED WHEN THEY ARE IN THE SAME
ROOM AS THE APPLIANCE.
OPERATION AND CARE OF YOUR
APPLIANCE
1. Appliance operation is controlled through
an on/off switch. Separate switches may
provide independent control for the optional
forced air kit and fireplace operation (see
Optional Equipment).
2. To light the appliance refer to the lighting
instructions located at the back of this manual.
Decorative Volcanic Stone
The decorative volcanic stone, Model DVS, can
be used to enhance the look of your appliance.
Spread the decorative volcanic stone evenly
around the bottom of the firebox.
One Piece Arch Kit
A one piece complete door arch kit is available
for use with these CF appliances. The kit is easy
to install and does not require hardware to
attach it to the standard door frame. This kit can
be retrofitted to previously installed appliances.
The one piece decorative arch kit can not be
used in conjunction with the screen panel kit.
Gas Flex Line with Valve
A gas flex line kit is available to aid in attaching
this appliance to the gas supply. This kit can
only be used where local codes permit. The kit
includes a ¹⁄₂" NPT to ³⁄₈" flare in line shut-off
valve, a 12" flex line ³⁄₈" female flare through and
a ³⁄₈" flare to ³⁄₈" NPT fitting. The components of
this kit are rated for both natural and propane
gas. This kit is designed to be used as an aid in
installing the appliance.
Screen Panel Kit
An optional screen panel can be installed on the
CF door. This screen panel is easy to install
using the provided hardware. The screen panel
can be installed with both ceramic and tem-
pered glass in the door. This kit can be retrofit-
ted to previously installed appliances. The screen
panel kit may not be used in conjunction with
the one piece decorative arch kits.
Remote Control Kit
The Model RCK adds the convenience of re-
mote control for your appliance. The kit in-
cludes a wireless, hand held transmitter and a
receiver that replaces the wall switch. This
special receiver permits either manual or re-
mote control modes. Both receiver and trans-
mitter operate on standard 9 volt batteries (not
included). Refer to the RCK installation instruc-
tion for specific details.
Brass Hood Kit
An attractive brass hood is available to be used
on the CF appliance. These hoods are designed
to be fitted to the face of the appliance above the
door. In addition to providing an aesthetically
pleasing appearance to your appliance installa-
tion, the hood reduces heat effects to decora-
tive mantles and finish materials located di-
rectly above the fireplace opening. The hood kit
includes the necessary attaching hardware. This
kit can be retrofitted to previously installed
appliances.
Note: Instructions are also found on the pull-
out panel located in the lower control compart-
ment of the appliance.
3. Flame Adjustments – These appliances
are equipped with a two stage, High (HI), Low
(LO) gas control valve. This valve provides
for easy flame height adjustment. To adjust
the burner between the HI and LO settings,
rotate the HI/LO knob, located in the center of
the valve front face, clockwise and counter-
clockwise respectively.
4. When lit for the first time, the appliance will
emit a slight odor for an hour or two. This is
due to the “burn-in” of the internal paints and
lubricants used in the manufacturing process.
Additionally, when lit for the first time, this
appliance may produce smoke, this is normal
and should be expected. For the first few
hours, operate the appliance with doors and
windows open to encourage the dissipation of
smoke and fumes.
5. Upon each lighting of the appliance, conden-
sation may occur and fog the inside of the glass
enclosure panel. This condition is normal and
will disappear as the glass surface heats.
6. Always keep the appliance area clear and free
from combustible materials, gasoline and other
flammable liquids.
7. Remember, these appliances have a con-
tinuous burning pilot flame. Exercise caution
when using products with combustible vapors.
WARNING: OBSERVE CAUTION NEAR THE
GLASS ENCLOSURE PANEL. THE GLASS
MAY SHATTER UNEXPECTEDLY OR IF
STRUCK WITH AN OBJECT.
Wall Thermostat Kit
A wall thermostat kit is available for use with
these appliances. The wall thermostat is de-
signed to be wired directly to the appliance
millivolt gas control circuit and provide auto-
matic On/Off control of the appliance to main-
tain a desired temperature within the room.