Filter
Top Products
Wireless Motion Sensor Model PS-103
The Motion Sensor is designed to monitor movement around / within
your house. Once motion is detected, the control panel will either alert
you or alarm will be triggered.
In this package, you should find a motion sensor, ball-head joint, and
screws.
Please follow the instructions below to set up the motion sensor.
1. INTRODUCTION
2. POWER UP THE WIRELESS MOTION SENSOR
3. LEARN SENSOR TO MA SERIES CONTROL PANEL (CONT)
4. INSTALLATION
Test
Button
LED underneath
the lens
Ball-head joint
2 pcs 3 x 18 screws
(Included)
Insert a 9V alkaline battery
(Not included) to the motion
sensor and its LED will be
on for 2 seconds.
3. LEARN SENSOR TO MA SERIES CONTROL PANEL
Control Panel will not respond to Motion Sensor unless:
1) The Control Panel is armed in Away Mode, it will respond to Motion
Sensors in Zones 1, 2 and 3;
2) Motion Sensor is programmed into Zone 4, which is a dedicated Alert
Zone.
It is important to select which zone you program the motion sensor to.
- If you setup the motion sensor for security purpose where it will cause
an alarm when an intruder break-in, you should program the Motion
Sensor to either Zone 1, 2 or 3. DO NOT program to Zone 4 as it is a
dedicated Alert Zone, sensors in this zone will not cause an alarm.
- If you setup the motion sensor for alert purpose where it does not need
to cause an alarm when motion is detected, you should program the
Motion Sensor to Zone 4. DO NOT program to Zone 1, 2, or 3 as Motion
Sensor in these zones will not provide any alert beeping indication.
Therefore, please select which zone you need to program the Motion
Sensor before proceeding further.
Step 1:
Press and hold the Learn Button on the Control Panel for 3 seconds.
Control Panel beeps once and you may release the Learn Button.
Step 2:
Press the zone button (1, 2, 3, or 4) once, for which you want to program
the sensor to. The selected Zone LED will flash.
MUTEMUTE
INPUT DC 12VINPUT DC 12V
LEARNLEARN
ALERTALERT
CHIMECHIME
OFFOFF
Press 3 sec.
Long Beep
Step 3:
Activate the Motion Sensor by pressing the test button on the back of the
Motion Sensor.
Step 4:
You will hear a long beep and the zone LED stops flashing. The sensor
is now programmed to the Control Panel.
Control Panel long beep
Zone LED flashing OFF
Press
Test Button
Note:
You may program up to 4 sensors to one zone.
Zone 4 is an alert zone, sensors in this zone is for alert purpose ONLY
and will not trigger the alarm.
After programming the motion sensor to the Control Panel, you may
place the Control Panel in Test Mode to verify the communication
between the Motion Sensor and the Control Panel.
Step 1:
Remove the adapter and all batteries from the Control Panel.
Step 2:
Press and hold the "Mute" button and plug the AC adapter back into the
Control Panel. All LED indicators will be ON, you may release the "Mute"
button. Control Panel is now in Test Mode, and it will respond to all
Motion Sensors and other sensors.
Step 3:
Place the Alert Notification Switch to "Alert" and you may now activate
the Motion Sensor by pressing the test button on the back of the Motion
Sensor. You may also move in front of the Motion Sensor. Please refer
to "Walk Testing" for detail information on how to walk test the Motion
Sensor.
Step 4:
Control Panel will respond by flashing the zone LED and alert beeping,
according to the zone number. 1 beep for zone 1, 2 beeps for zone 2 etc.
The beeping will last around 15 seconds for each activation.
After testing, unplug the AC adapter and plugs it back into the Control
Panel, it will back to Normal Operating Mode.
Test Sensor
You may now close the battery
cover and re-insert the screw.
Mount the ball-head joint on
the wall with screws provided.
Slide the back of the sensor into
the ball-head joint. The mounting
angle can be adjusted.
Walk Testing
Walk test should be performed after the motion sensor
is mounted. Walk in the detected area, if motion is
detected, a red light inside the sensor will glow. If the
red light does not glow, motion has not been detected
and you may need to re-position the sensor. Ensure
you walk test all the locations that you would like the
motion sensor to cover.
Motion Sensor
Press the zone button
Zone LED flashing