Filter
Top Products
There are
3 different operating modes for the Household Alert@ Long
Range
Receiver.
1) Alert
-
Beeps when
a sensor is activated,
corresponding
zone
LED
will also flash.
2) Alarm
-
Sounds
an alarm
when
a sensor is
activated, corresponding
zone LED
will also flash.
3) Off
-
No
audio sound
will
be emitted when
sensor
is
activated.
Zone LED
will flash to indicate the
activated sensor.
To select
the
operating mode,
place
the
slide switch on the
side
at the
desired setting:
OFF
-
No Audio
ALERT
-
Alert
Mode
ALARM
-
Alarm Mode
Operation
Alert
When motion
is detected in the monitored
area,
the
sensor
will send a
signal
to the receiver. lt will
beep and the corresponding zone
red LED
will
flash for
15
seconds.
lf the sensor is
set to zone
1, zone
1 red LED on the receiver will
flash,
and
the receiver
will emit a continuous
"single
beep",
i.e.
"beep"
pause,
"beep", pause.....
etc.
lf the sensor is
set to zone
4,
zone 4 red LED will
flash, and the
receiver
will
emit a continuous
"4
beeps", i.e.
"beep
beep
beep beep"
pause
"beep
beep
beep beep"
pause
......etc.
By the number
of beeps emitted by the receiver,
user can
identify which
zone is triggered.
Mute
When a
sensor is triggered for
a long
period
of time,
you
may
stop
the
buzzer by
pressing
the mute button. When
another
signal comes again.
you
can disable
lhe buzzer for
all currently activated
sensors by
pressing
the mute button.
The receive will
beep again if
it receives another signal.
For instance,
if
you
are working in
your
garage, you
may want to
disable the
buzzer
for
this
garage
only. Then
you
can
press
the
"Mute"
button after it
starts to
sound.
lf
any
other sensor is triggered,
the receiver
will
sound again.
Alarm
When the receiver
is in Alarm
operation mode,
it will
sound
its
siren
when a sensor
is
activated.
The
maximum
alarm
duration is set for 3
minutes. To
terminate
the siren
during the
3-min interval,
press
the mute
button. Although
the
alarm siren is terminated,
if
that sensor is still
activated,
its
corresponding LED
will continue
to flash.
Note: This
audio
siren
is
not intended
to
prevent
intruder
break-in,
it
is
rather
an alert
signal indicating
a
sensor
is
activated. Therefore,
turning
off the
siren does not require
specific
password.
off
No audio will
be emitted
even sensor is activated.
Only zone LED will
flash.
When the
battery
level on the
sensor drops to
a certain
level,
or
the
sensor
is
out
of the operating range,
the receiver will
show a
"loss
of
signal"
indication.
The
red LED representing
that zone will flash rapidly,
i.e. if zone 1
sensor is lost, the zone
1 red LED will flash rapidly.
When the loss
of
signal
indication
occurs,
move the receiver closer
to
the
corresponding
sensor and trigger that
sensor. lf the red LED
stops
flash-
ing rapidly,
that means
the receiver
or sensor needs
to be
relocated. lf the
"loss
of signal"
indication
persists,
replace the
battery of that sensor.
The Household
Alert@ Long Range Receiver
can work with up to 4
different sensors:
garage
door monitor
sensor, door /
window
sensor,
water sensor, indoor/outdoor
motion sensor,
etc.
Please visit
www.skylinkhome.com
or contact us at support@skylinkhome.com for
more information of how
to fully utilize
your
lndoor/Outdoor Motion
Sensor.
This device complies with Part
15 of the FCC Rules.
Operation
is
subject
to the
following two conditions:
(1)This
device may not cause harmful interference, and
(2)
This
device must accept
any
interference
received, including interference that
may cause undesired
operation.
WARNING:
Changes
or modifications to this
unit
not
expressly approved by the
party
responsible
for
compliance could void the user's authority to operate the equipment.
NOTE:
This equipment has been tested
and
found
to comply with the limits for a Class
B
digital device,
pursuantto
Part 15
of
the FCC Rules. These limits
are designed
to
provide
reasonable
protection
against harmful interference in
a
residential installation
This equipment
generates,
uses and can radiate radio frequency energy and,
if not
installed and used in
accordance with the instructions, may cause harmful inter-
ference to
radio
communications.
However,
there is
no
guarantee
that interference will
not occur in a
particular
installation.
lf this
equipment dose cause harmful interference
to radio or television
reception,
which
can be determined by turning
the equipment off and on, the user
is
encouraged
to try to
correct the interference by
one or
more
of the
following measures:
-
Reorient or relocate
the receiving antenna.
-
lncrease the separation
between the equipment and receiver.
-
Connect
the
equipment into
an outlet on a circuit different from that to which the
receiver is
connected.
-
Consult
the dealer
or an experienced radioffV
technician for help.
lf, within
one
year
from
date of
purchase,
this
product
should become defective
(except
battery), due to faulty
workmanship
or
materials,
it will be repaired or
replaced, without
charge. Proof
of
purchase
and a Return Authorization
are
required.
lf
you
would
like
to
order Skylink's
products
or have difficulty
getting
them to
work or
download information
and user manual,
please
:
1. visit our FAQ
section at www.skylinkhome.com,
or
2. email
us
at
support@skylinkhome.com,
or
3. call ourtollfree
at 1-800-304-1187 from
Monday to Friday,
9 am to 5
pm
EST.
Fax
(800)
286-1
320
CUSTOMER SERVICE
17
Sheard
Avenue,
Brampton,
Ontario, Canada L6Y
1J3
Email :support
@
skylinkhome.com
http;//www.skyl i n khome.
com
P/N.1Un54
O2O1O
SKYLINK GROUP