Filter
Top Products
CUSTOMER SERVICE
Email:support@skylinkhome.com (Reply within 24 hrs)
http://www.skylinkhome.com
P/N. 101A227-001 Rev.1
©2003 SKYLINK GROUP
When motion is detected in the monitored area, the sensor will send a signal to the receiver. It
will beep and the corresponding zone red LED will flash for 15 seconds.
If the sensor is set to zone 1, zone 1 red LED on the receiver will flash, and the receiver will emit
a continuous “single beep”, i.e. “beep” pause, “beep”, pause….. etc.
If the sensor is set to zone 4, zone 4 red LED will flash, and the receiver will emit a continuous “4
beeps”, i.e. “beep beep beep beep” pause “beep beep beep beep” pause ……etc.
By the number of beeps emitted by the receiver, user can identify which zone is triggered.
4. OPERATION
3. POWER UP THE INDOOR/OUTDOOR MOTION SENSOR (CONT)
When the battery level on the sensor drops to a certain level, or the sensor is out of the operating
range, the receiver will show a “loss of signal” indication. The red LED representing that zone
will flash rapidly, i.e. if zone 1 sensor is lost, the zone 1 red LED will flash rapidly.
When the loss of signal indication occurs, move the receiver closer to the corresponding sensor
and trigger that sensor. If the red LED stops flash-ing rapidly, that means the receiver or sensor
needs to be relocated. If the “loss of signal” indication persists, replace the battery of that sensor.
5. LOSS OF SIGNAL INDICATION
8. WARRANTY
If you would like to order Skylink’s products or have difficulty getting
them to work, please :
1. visit our FAQ website at www.skylinkhome.com, or
2. email us at support@skylinkhome.com (reply within 24 hrs), or
3. call our toll free at 1-800-304-1187
from Monday to Friday, 9 am to 5 pm EST.
Fax +800 286-1320
9. CUSTOMER SERVICE
If, within one year from date of purchase, this product should become
defective (except battery), due to faulty workmanship or materials, it will
be repaired or replaced, without charge. Proof of purchase and a Return
Authorization are required.
After mounting the sensor at the desired location,
it is important to perform a walk test in order to
determine if the sensor is detecting the things you
want to detect.
In order to control how far the sensor can “see”, this can be done by
adjusting the angle of the sensor. To reduce the detection range, simply
move the sensor downward. To increase the range, move the sensor
up to around 12 degrees. This will give the maximum range. However,
this may not be desired if the sensor is placed outdoors, since a false
trigger may occur if the sensor is set to detect motion in a distance.
You should walk in the area that you would like the sensor to monitor.
The receiver will beep if the sensor detects your movement. If the
receiver does not respond, adjust the mounting angle accordingly.
Perform the walk test again after 30 seconds. Repeat this procedure
until your motion is detected. There should be no movement in the
detected area during the 30 seconds.
Perform walk test in the undesired area to ensure movement cannot be
detected.
Tips: The sensor should not face towards direct sunlight, placing near
heat or cold producing devices (i.e. A/C or furnance vents, fans,
ovens, heaters etc.) that may cause false triggers.
4. WALK TEST
This device complies with Part 15 of the FCC Rules. Operation is subject
to the following two conditions: (1) This device may not cause harmful
interference, and (2) This device must accept any interference received,
including interference that may cause undesired operation.
WARNING:
Changes or modifications to this unit not expressly approved by the party
responsible for compliance could void the user’s authority to operate the
equipment.
12º
6. OTHER HOUSEHOLD ALERT
TM
SENSORS
The Houselink
®
receiver can work with up to 4 different sensors: garage door monitor sensors,
door / window sensors, water sensors, indoor/outdoor motion sensors, etc. Please visit
www.skylinkhome.com or contact us at support@skylinkhome.com for more information of how
to fully utilize your Indoor/Outdoor Motion Sensor.
7. FCC