Filter
Top Products
If your Sears
®
, Chamberlain
®
or Lift-Master
®
transmitter has three buttons
(two small, one large) (Diagram G) then the button that operates the
receiver will determine how to set the number 1 DIP switch of the Skylink
transmitter. If the large button is used to operate the unit, set the #1 DIP
switch to “ - ” position; if the middle button is used, set the #1 DIP switch
to the center position; if the button at the end is used, set the #1 DIP
switch to " + " position. Set the other DIP switches (DIP switch #2 onward)
to match the setting of your existing transmitter.
Note - ‘LEARN CODE’ Some transmitters/receivers do not have DIP switches,
this means they can “learn” new code settings. Just set the DIP switches
on our keypad to any code combination. Press the learn button, (located
on the back of the garage door receiver located in the ceiling of the garage),
for 2 seconds then release, so that the light beside the learn button goes on.
While the light is on, enter the 4 digit pin number,
(currently set at 0000), then press the [#] key.
If the light beside the learn button flashes, the
operator has now learned and will recognize
the keypads code.
Linear Position 1 to 8 + OR -
M-O-M Position 1 to 8 + OR -
Stanley (310) Canada Position 1 to 10 + OR - 11,12 set to ‘+’ or ‘-’
Stanley (300) Position 1 to 10 + OR - 11,12 set to ‘+’ or ‘-’
Multi-Code Position 1 to 10 + OR - 11,12 set to ‘+’ or ‘-’
Chamberlain Position 1 to 9 +, 0 , OR -
Lift-Master Position 1 to 9 +, 0 , OR -
Sears Position 1 to 9 +, 0 , OR -
Wayne Dalton Position 1 to 9 +, 0 , OR -
Master Mechanic Position 1 to 9 +, 0 , OR -
Genie (9 positions) Position 1 to 9 + OR -
Genie (12 positions) Position 1 to 12 + OR -
Overhead Position 1 to 9 +, 0 , OR -
Martec/Teckey Position 1 to 10 + OR - 11,12 set to ‘+’
Pulsar/Allister/Allstar Position 1 to 9 +, 0 , OR -
4c. If your existing transmitter or receiver has fewer than12 switches,
match only the first corresponding DIP switch. Leave the remaining
posts in center position “0”.
4d. Enter the current 4-digit PIN, on the keypad of the Model G5K, then press
[#] will activate the garage door opener. If you have just purchased
the Model G5K, the factory default 4-digit PIN is 0000.
So please enter [0], [0], [0], [0], [#].
If the garage door does not open,
reverse all of the DIP switch on
the model G5K. The “ + ” will be
changed to the “ - “ position and
the “ - ”position will be changed
to the “ + ” position (see diagram F).
Also try the unused DIP switches
in the “ + ”, “ 0 ” or “ - ” positions.
Original Position
Reversed Position
Diagram F
Code connector setting to match your opener/motor
Diagram G
- Position the keypad on the garage door
frame.
- Lift up the cover and insert screw above
the keypad in the slot provided (a).
- Remove the battery cover and insert the
second screw in the lower slot (b).
- Replace the battery cover and insert
screw (c).
- To change your PIN:
1. Enter the current PIN, (currently set at 0 0 0 0), press ,
2. Enter new 4 digit PIN, press ,
3. Enter new PIN again, press .
For example, if you are changing the PIN number from 0000 to 1234,
enter the following sequence, 0000, ,1234, ,1234, .
If confirmed, the backlit LED flashes and the unit emits a long beep.
*
*
*
*
* *
- Operation
Press [ PIN ] , [#] To open or close garage door, press your four digit
PIN and the [#] key. If confirmed, the model G5K will emit three beeps.
If you do not hear 3 beeps after the 4-digit PIN and [#] is entered, that means
you have entered an incorrect PIN, and the Model G5K will not operate your
garage door.
Two 3 volt Lithium type (CR2032) batteries (included).
It is time to change the batteries when the backlight no longer appears.
+
-
Battery
Compartment
If your Sk ylink Universal Remote Control does not activate your Garage Door
Opener, the reason may be that your GDO age or manufacturer is not listed on the
compatibility chart.
The solution is the Skylink SG-18R Universal Receiver.
If you would like to order Skylink’s product or have difficulty getting your Skylink’s
remote control to work, please :
1. visit our website FAQ at www.skylinkhome.com, or
2. email us at support@skylinkhome.com
3. call our toll free at 1-800-304-1187 from Monday to Friday, 9 am to 5 pm EST.
fax: 1-800-286-1320
(a)
(c)
(b)
Examples of how to set Model G5K
Diagram E
Existing
Transmitter
CUSTOMER SERVICE
17 Sheard Avenue, Brampton, Ontario, Canada L6Y 1J3
Email:support@skylinkhome.com
http://www.skylinkhome.com
P/N. 101A400
US Patent. 5680134, 5841390, 6005508, 6956460
® are registered trademarks of their respective corporations
©2005 SKYLINK GROUP
Model G5K
2. PROGRAMMING YOUR NEW TRANSMITTER (CONT)
3. INSTALLATION
6. WARNING
If this transmitter triggers other garage doors in your neighborhood, change all your
transmitters and receiver to a new code setting.
DO NOT let children use the garage door transmitter without adult supervision.
Children can injure themselves or others by the garage door.
5. BATTERY
7. FCC
The Universal Garage Door Remote Control is approved by the FCC and it complies
with Part 15 of the FCC Rules. Its operation is subject to the f ollowing two conditions :
1. This device may not cause harmful interference.
2. This device must accept any interference that may cause undesired operation.
WARNING:
Changes or modifications to this unit not expressly approved by the party
responsible of compliance could void the user’s authority to operate the equipment.
8. WARRANTY
If, within one year from date of purchase, this product should become defective
(except battery), due to faulty workmanship or materials, it will be repaired or
replaced, without charge. Proof of purchase and a Return Authorization are required.
9. CUSTOMER SERVICE
NOTE:
The backlight comes on and a beep is emitted when any key is pressed.
The backlight of the key pad may not be visible when it is too bright outside.
When any key is pressed, the next key must be pressed within 5 seconds or
the backlight turns off and the sequence is canceled. You must begin again.
If the keypad does not emit a beep when pressed, wait a few seconds
and press the key again. If you hear a beep, the keypad has accepted
that key.
4. KET PAD OPERATION