Filter
Top Products
Thank you for your purchase of the Skylink garage door remote control,
Model G5K. There are 3 different steps you need to setup in order to
use this universal garage door remote control to operate your existing
garage door opener. These 3 steps are:
1) Frequency switch – select the correct frequency according to the
brand of your existing garage door opener.
2) Brand jumpers – place the brand jumpers at the correct position
according to the brand of your existing garage door opener.
3) Code setting – Set the DIP switch on the Model G5K so that they
match the code setting of your existing garage door opener.
In this package, you should find a wireless keyless entry with two 3V
lithium battery.
Please follow the detailed instructions below in order to set-up the
Skylink Model G5K to work with your existing opener.
ABCD
USA
CANADA
A
300
310
B
310
315
C
315
318
D
390
390
2a.The Model G5K contains 2 brand jumpers and 12 DIP switches (see
diagram B). The brand jumpers are located just above the DIP switches
with markings “A” and “B”. There are 2 connectors, one is placed on
the “A” column, the other one is placed on the “B” column. For each
column, there is a connector. If the connector
is placed on the top and middle post of that
column, that column is set on “+”. If the con-
nector is placed on the middle and bottom posts,
that column is set on “-“. If the connector is
removed completely, that column is set on “0”
(see diagram B). In order for the Model G5K to
work with your existing garage door opener
(motor), you need to set the brand jumpers
based on the brand of your existing garage
door opener. Please set these 2 brand jumpers
“A” and “B” based on the brand jumpers setting
on chart 2. Please identify the group number on
chart 2 in order to determine which is the next
step to proceed.
Wireless Keyless Entry
Model G5K
Wireless Keyless Entry
(Battery inside)
1a. Locate frequency switch on the top
of the transmitter. (See diagram A)
Diagram A
Chart 1
Chamberlain
®
Lift-Master
®
Sears
®
Wayne Dalton
®
Master Mechanic
®
Genie
®
Overhead
®
390MHz only
Linear
®
M-O-M
®
Stanley
®
Multi-Code
®
Martec/Teckey
®
Skylink
®
UR-100
Pulsar
®
/Allstar
®
/Allister
®
Linear
®
MegaCode
TM
Skylink
®
18 series
315 or 390
315 or 390
315 or 390
300 or 390
390
390
390
310
310
310
300 or 310
300
390
Brand of your opener
C or D
C or D
C or D
A or D
D
D
D
B
B
B
A or B
A
D
B or D
B or D
B or D
B or D
B or D
B or D
D
A
A
A
A
D
C
C
C
315 or 390
315 or 390
315 or 390
315 or 390
315 or 390
315 or 390
390
310
310
310
310
390
318
318
318
N/A
N/A
N/A
N/A
1b. Determine the brand of your garage
door opener and set the frequency
switch to the corresponding position.
(See chart 1)
2. PROGRAMMING YOUR NEW TRANSMITTER
1. SET FREQUENCY SWITCH
2. SET BRAND JUMPER
2. PROGRAMMING YOUR NEW TRANSMITTER (CONT)
* Note:
For Genie
®
Intellicode
TM
& Overhead Code Dodger
TM
, if the brand
jumper for group 3 cannot operate your garage door opener properly,
please use setting A “-”, B “+”.
For garage door openers belonging to groups 1 to 5, please follow
step 3 of the procedures, this will complete the setup. No need to proceed
to step 4.
For garage door openers belonging to groups 6 to 0, you can
proceed directly to “Step 4 – Set DIP switches” after you have success-
fully set the brand jumpers. Please skip step 3 below.
Diagram C
‘Learn’ Button
Garage Door
Opener (GDO)
Note:
Proceed to this step only if the brand of your garage door opener
belongs to either group 6, 7, 8, 9 or 0 on chart 2. Otherwise, proceed
to Step 3 - Learn code.
4. SET DIP SWITCHES
Group Brand Brand jumpers setting Proceed to
A B
1 Chamberlain
®
, Sears
®
, Lift-Master
®
(without DIP switches but with red, orange or purple + -
learn button)
2 Chamberlain
®
, Lift-Master
®
, Sears
®
, Wayne Dalton
®
, - 0
Master Mechanic
®
(without DIP switches but with
yellow, white, gray or green learn button)
3* Genie
®
Intellicode
TM
* (without DIP switches) + +
Overhead Code Dodger
TM
* (without DIP switches)
4 Linear
®
MegaCode
TM
(Canada only) 0 -
5 Skylink
®
18 series
(Canada only) 0 0
6 Genie
®
(with DIP switches), Overhead
®
+ 0
7 Chamberlain
®
, Lift-Master
®
, Sears
®
, Wayne Dalton
®
, - +
Master Mechanic
®
(with DIP switches)
8 Stanley
®
, Multi-Code
®
, Martec
®
- -
9 Linear
®
, Moore-O-Matic
®
0 +
0 Pulsar
®
/ Allstar
®
/ Allister
®
(Canada only) 0 -
Chart 2
Proceed
to Step 3.
Proceed
to Step 4,
skip Step 3.
3. LEARN CODE
Note:
Proceed to this step only if the brand of your garage door opener
belongs to either group 1, 2, 3, 4 or 5 on chart 2. Otherwise, proceed
to Step 4 - Set DIP switches.
3a. If your existing garage door opener belongs to any brand from group 1, 2,
3, 4 or 5, then you should find a “learn” button from the garage door
opener (the unit with the motor located on the ceiling of your garage,
see diagram C). Press this learn button for approximately 2 seconds.
The LED light beside the learn button will go on and then enter the
current 4-digit PIN, on the keypad of the Model G5K, then press [#] key.
If you have just purchased the Model G5K, the factory default 4-digit PIN
is 0000. So please enter [0], [0], [0], [0], [#]. This will activate the
Model G5K and radio signal will be sent to your existing garage door
opener. If the garage door opener learns the code, the LED light on
the garage door opener will flash then go off. The Model G5K is now
programmed to your existing garage
door opener and will operate your
garage door. Programming is now
completed and please refer to
“Keypad Operation” for changing
your personal PIN and other operations.
4a. If the brand of your garage door opener
belongs to groups 6 to 0, that means you
need to program the correct DIP switch
setting in order for the Model G5K to work
with your existing garage door opener.
There are 12 DIP switches numbered
from 1 to 12. (see diagram D)
4b. Use a pen to set the DIP switches to match
the code of your existing transmitter or receiver.
DIP Switch Location
Diagram D
Pen
Each DIP switch of this keypad has 3 positions ( " + ", " 0 ", " - " ). If the
switches of your existing receiver (Stanley
®
, Genie
®
, Multi-Code
®
,
Linear
®
, Moore-O-Matic
®
, Martec
®
) have only two positions, set the
switches of the model G5K to " + " for ON or CLOSE, and " - " for OFF or
OPEN (Do not use " 0 " center position.) (see diagram E). If the switches
of your existing transmitter (Chamberlain
®
, Sears
®
, Lift-Master
®
, Wayne
Dalton
®
, Pulsar
®
or Master Mechanic
®
) have 3 positions, set the DIP
switches of the model G5K to match their corresponding positions.
1. INTRODUCTION
A = “+” B = “-”
Diagram B
Brand
Jumper
REMOVE JUMPER = “0”
Set switch
to position Frequency
USA
Set switch
to position Frequency
CANADA