Filter
Top Products
OPERATING INSTRUCTIONS
6
Fig. 11
6. Vigorously “TapClean”
the HEPA Dust Cup
Filter on a hard
surface until no more
dust is observed
falling out from
between the pleats of
the filter. (Fig. 11)
Fig. 12
Debris
Screen
7. “TapClean” the Debris
Screen or rinse under
a faucet until clean.
(Fig. 12) Remember
that the Debris Screen
must be completely
dry before reinstalling
in the vacuum.
8. Replace the Debris Screen on the
HEPA Dust Cup Filter and reinstall
filter assembly in the vacuum. (not
shown)
PLEASE NOTE: The white pleated
filter material in the HEPA Dust Cup
Filter will discolor over time -This is
NORMAL and will NOT affect the
performance of the filter. If the HEPA
Dust Cup Filter
is properly
"TapCleaned”
after each use
and suction
does not return
to 100%, then
we suggest that
the HEPA filter
be “TapCleaned”
vigorously until no
more dust can be removed, then
rinsed under the faucet and allowed to
dry for 24 hours before refitting into
the vacuum. (Fig. A) This should be
done once a month or when
suction appears reduced.
CAUTION: The suction hole must be
open and free of any obstructions at
all times. Otherwise, the motor will
overheat and could become
damaged.
Fig. A
Wash once a
month or when
suction
appears
reduced.
.
Warning: Allow 24
hours for drying before
replacing in unit.
IMPORTANT: This unit is equipped
with a motor protective thermostat. If
for some reason the vacuum cleaner
should overheat, the thermostat will
automatically turn the unit off. Should
this occur:
• Push the On/Off button once.
• Disconnect the plug from the
power source.
• Check the source of overheating
problem. (i.e. clogged hose or
filter)
• If clogged hose or filter is found,
unclog the hose and replace the
filters.
• Wait at least 45 minutes before
attempting to reuse the vacuum.
• After unit has cooled down for
45 minutes, plug in the cleaner
and push the On/Off button. The
vacuum should start again.
• If the vacuum still does not start,
contact customer service at
1 (800) 798-7398.
Motor Thermostat
13
3. Para usar la manguera flexible con
la escobilla para polvo, sostener la
manguera en una mano y con la
otra mano tirar de la escobilla para
polvo girándola en el contra sentido
del reloj hasta que salga y
enganche en posición. (Fig. 4)
Aspirado con Manguera
Para usar la aspiradora sólo con
manguera y la escobilla para polvo o
la boquilla para rendijas:
1. Girar la tapa de la cámara de la
escobilla motorizada presionando
el botón de seguro hasta que
enganche en posición.
2. Sacar la manguera flexible de la
salida de la cámara de la
escobilla y desenganchar la
manguera de su soporte. (Fig. 3)
CUIDADO: La aspiradora de mano es
muy potente. Asegurarse de sostenerla
firmemente, de lo contrario podría
escaparse de la mano y causar
lesiones.
Fig. 1
Fig. 2
Fig. 3
Fig. 4
4. Para usar la manguera flexible con
la boquilla para rendijas, cerciorarse
que la manguera esté en posición
de guardada e insertar la boquilla
para rendijas, en la boca de la
manguera. (Fig. 5)
Fig. 5
INSTRUCCIONES PARA OPERAR
ADVERTENCIA: Siempre
desenchufar del tomacorriente antes de
abrir el compartimiento del colector de
polvo.
Nota: Siempre que se opere la
aspiradora debe tener instalado el filtro
HEPA.
Uso como Aspiradora de Mano
1. Insertar el conector de la manguera
para escobilla de polvo en la salida
de la cámara de la escobilla
motorizada. Asegurar la manguera
en el soporte para manguera. (Fig. 1)
IMPORTANT: This unit is equipped
with a motor protective thermostat. If
for some reason the vacuum cleaner
should overheat, the thermostat will
automatically turn the unit off. Should
this occur:
• Push the On/Off button once.
• Disconnect the plug from the power
source.
• Check the source of overheating
problem. (i.e. clogged hose or filter)
• If clogged hose or filter is found,
unclog the hose and replace the
filters.
• Wait at least 45 minutes before
attempting to reuse the vacuum.
• After unit has cooled down for 45
minutes, plug in the cleaner and
push the On/Off button. The
vacuum should start again.
• If the vacuum still does not start,
contact customer service at
1 (800) 798-7398.
Motor Thermostat