Shark S3325 Vacuum Cleaner User Manual


  Open as PDF
of 7
 
-
~
Filling
your
Canister
Steam
Cleaner
with
Water
IMPORTANT:
Always insure that the
unit is UNPLUGGED from the wall
receptacle and all switches are in the "Off'
position prior to initial filling or re-filling
til e
water tank .
Never
attempt
to
fill
this
unit
under
a
water
tap
,
always
use
the
filling
flask
and
funnel
provided.
Failure to
follow these steps will cause the water
tank to overfill and may pose an electrical
safety hazard.
RECOMMENDATION
: The use of
distilled/demineralized water is
recommended, particularly in areas with
hard water in order to prevent the build-up
of lime scale .
Step 1: Press the safety cap down and
turn counter clockwise until
removed .
Step 2: Assure that the steam cleaner is
empty so that the addition of the
prescribed amount of water will
not result in overfilling.
Step 3: Add 47 fl. oz (1400 ml) of water
using the filling flask and funnel
provided. (Fig. 1) Do
not
overfill.
Replace safety cap by
turning clockwise - press down
firmly to tighten. Heating time is
approximately
8-10
minutes
.
Fill:ng the boiler with hot water
will shorten heat up time.
Step 4: Connect the desired accessory
onto the steam hose.
Step 5: Plug the unit into a standard
120 volt wall receptacle. Press
the On/Off switch. The Heating
light (Red) will light up.
Step 6: Allow
approximately
8-10
minutes for water vapor to reach
its working temperature. When
the unit is ready for use the
steam ready light will light up.
Step 7: Upon initial use, some water
will come out from the hose
nozzle. This is residual water
that is left over in the hose from
the last use and is normal.
Jt..
CAUTION:
Always
point
the
....
nozzle
outlet
in a safe
direction
.
Never
point
in the
direction
of
ourself.
other
people
or pets.
Fig. 1
NOTE:
When the steam cleaner has
run out of water, steam output will
cease.
Refilling
Unit
Wah
Water
Jt..
WARNING :
Always
allow
the
....
unit
to
cool
for
15
minutes
before
re-filling.
When
re-filling
the
steam
cleaner
while
it is
still
hot,
the
first
drops
of
water
might
bubble
up . Use
caution
when
opening
the
safety
cap as cap
may
become
hot
during
use and
escaping
steam
can
cause
scalding.
Step 1: Press the On/Off button on
the unit to the "Off' position .
Step 2: Press the On/Off steam
switch to the "On" position
and wait until no more steam
comes out of the hose.
Step 3: Remove the plug from the
electrical outlet and allow the
unit to cool for
approximately
15
minutes
before refilling
with water.
Step 4: After completing the cool
down period of step 3 (above),
carefully press down on the
safety cap and turn counter
clockwise to loosen.
OPERATING INSTRUCTIONS
Step 5: Slowly pour water using the
filling flask and funnel provided
into the boiler. DO NOT
fill
under
a faucet.
Always
use
the
filling
flask
and
funnel
that
are
provided
. DO NOT OVERFILL.
Never
put
more
than
47
ounces
(1400 ml)
of
water
in
the
unit
at
one
time.
Step 6: Screw safety cap back on to the
unit by turning clockwise and
press down to tighten securely.
Plug appliance back into wall
outlet. Steam will start to be
produced as before.
Using
Your
Steam
Cleaner
with
Steam
Pocket
Step 1:
NOTE:
Step 2:
Connect one of the extension
tubes to the hand grip on the
flexible steam hose. To attach
the extension tubes one onto the
other or onto the hand grip, press
the locking button ensuring that it
fits into the hole. (Fig. 2) To
disconnect, repeat the operation
by pressing the locking button
and pulling the two sections
apart.
Fig. 2
~
,
"
Fit the stearn pocket frame with
the angle adapter onto the
extension tube.
If the angle adapter is not
attached to the steam pocket
frame, attach as follows: Hold
the steam pocket
frame in one hand
and the angle
adapter in the
other. Insert the
angle adapter
stem into the -
Fig. 3
opening of the steam pocket
frame as shown in Fig. 3.
Note that the flat on the nozzle
must face toward the side of
the frame with the brass pin.
Once inserted,
rotate
it 90°.
Attaching
the
Steam
Pocket
Towel
to
the
Frame
Jt..
WARNING:
Always insure the
....
unit is UNPLUGGED from the wall
receptacle prior to attaching or
removing accessories.
1. Slide the steam pocket towel over the
steam pocket frame. (Fig.
4)
2. Bring the towel all the way to the
top of the steam pocket frame.
(Fig. 5)
3. Bring the velcro strips that are on the
back side of the steam pocket towel
over the steam pocket frame and
attach to the inside of the front side of
the steam pocket towel. (Fig. 6)
5
6
 previous next