Filter
Top Products
OPERATING INSTRUCTIONS
DIRECTIVES D’USAGE
Cleaning the HEPA Filter and the
Debris Screen
INSERTION DE LA POIGNÉE
DANS LE CORPS DE
L’ASPIRATEUR
• Insérez la poignée dans l’orifice du
haut de l’appareil. Assurez-vous que
la fente de la poignée s’insère
correctement dans l’ouverture (Fig. 1).
• Pour retirer la poignée, appuyez sur le
bouton de relâche et tirez la poignée
vers le haut.
FIXATION DU BOYAU AU
CORPS DE L’ASPIRATEUR
• Tenez une extrémité du manche
amovible du boyau et insérez-la
dans le connecteur à boyau (Fig. 3).
Connecteur à
boyau
Fig. 3
Boyau
d’entrée
Fig. 1
Connecteur
de la
brosse
Fig. 2
Bouton de
relâche de la
brosse
AVERTISSEMENT: Toujours
débrancher l’aspirateur avant l’assemblage
ou l’enlèvement d’accessoires.
3. Remove the HEPA
filter from the debris
screen. Remove the
filter ring that is
around the HEPA
filter. Then
vigorously “TapClean” the HEPA
Filter on a hard surface until no
more dust is observed falling out.
4. To clean the debris
screen, we
recommend that
you rinse it under
lukewarm running
water to remove
the dirt that
accumulates
on it, but always
allow 24 hours to air dry before
inserting back into the vacuum.
5. To re-assemble the filter
assembly, insert the filter ring over
the HEPA filter and then insert the
HEPA filter assembly into the
debris screen. Insert the debris
screen into the filter cover.
Replace the filter assembly into
the dust cup.
Warning: After each Use -
Always remove the Filter
Assembly, then vigorously “TapClean”
HEPA Filter and clean Debris Screen
until no more dust can be removed.
IMPORTANT
, Please Note : The
“TapClean” HEPA Filter will stop most of
the tiniest dust particles and airborne
allergens from re-entering the air you
breathe. In fact it stops 99.97% of all
particles as small as 0.3 microns - many
times smaller than a human hair!!!
Because of this incredible filtration
performance, the HEPA Filter will quickly
accumulate, inside the white filter folds,
many fine dust particles that are difficult
to see but which will eventually block or
reduce your suction power - if not
cleaned properly.
1. To remove the filter assembly from
the dust cup, hold the dust cup from
the handle in one hand and with the
other hand, turn counter clockwise
and pull out the filter cover. (Fig. 14)
Fig. 14
Wash
once a
month or
when
suction
appears
reduced
Warning: Allow 24
hours for drying before
replacing in unit.
Fig. A
PLEASE NOTE: The white pleated
filter material in the HEPA Filter will
discolor over time -This is NORMAL
and will NOT affect the performance
of the filter. If the HEPA Filter
is properly
"TapCleaned”
after each use
and suction
does not return
to 100%, then
we suggest that
the HEPA filter
be “TapCleaned”
vigorously until
no more dust
can be removed,
then rinsed under the faucet and
allowed to air dry for 24 hours before
refitting into the vacuum. (Fig. A)
This should be done once a month
or when suction appears to be
reduced .
2. To separate the filter assembly, hold
the bottom of the debris screen and
pull the filter cover out. (Fig. 15)
FIXATION DE LA BROSSE À
PLANCHERS AU CORPS DE
L’ASPIRATEUR
• Insérez la brosse à planchers dans le
bas de l’aspirateur, dans la direction
indiquée par la flèche (Fig. 2).
• Assurez-vous que la brosse à
planchers est bien insérée son orifice.
• Insérez le boyau d’entrée dans le
connecteur de la brosse à planchers
(Fig. 3).
• Pour retirer la brosse du corps de
l’aspirateur, appuyez sur le bouton de
relâche de la brosse et tirez la brosse
hors de l’orifice.
Filter Cover
HEPA Filter
HEPA Filter Ring
Filter Assembly
Fig. 15
Connecteur de la
brosse
Debris Screen
26 7