Filter
Top Products
Tel: 1-800-662-0800 (Domestic U.S. & Canada) Email: info@seco-larm.com Website: www.seco-larm.com
16842 Millikan Avenue, Irvine CA 92606 Tel: 1-949-261-2999 (California and International) Fax: 1-949-261-7326 mi-SLI 762FP-ISS OWNERS.docx
SECO-LARM
®
1. VALET MODE – The Immobilizer automatically arms 30 seconds
after the engine is turned OFF. However there may be certain
times (for repair or if the Touchkeys are lost, for instance) that
arming the Immobilizer is not desired. Note: When in the
valet/override mode, the LED flashes while the ignition is turned
OFF to help deter thieves. When the ignition is turned ON, the LED
will turn OFF.
2. EMERGENCY DISARM – If the Touchkey is lost, the engine will not
start, even with the proper car keys. In this case, the Immobilizer
must be put into the valet/override mode using the emergency
disarm procedure.
3. EMERGENCY DISARM/VALET MODE
Note: Immobilizer must be armed before you can enter your PIN.
a. Know the secret PIN. For the following example, assume the
PIN is 503. Note: Count 10 flashes for the number “0”.
b. While the LED is flashing (because the Immobilizer is armed),
turn the ignition ON. The LED will show steady ON.
c. Turn the ignition OFF and the LED will start flashing. Count
the flashes. After the 5
th
flash, turn the ignition ON. The LED
will show steady ON again. (This is your PIN’s first digit—5.)
d. Turn the ignition OFF and count the flashes. After the 10th
flash, turn the ignition ON. The LED will show steady ON
again. (2nd digit, 0)
e. Turn the ignition OFF and count the flashes. After the 3rd
flash, turn the ignition ON. The LED will show steady ON
again. (3rd digit, 3)
f. At this point, the LED will show steady ON for 10 seconds then
OFF to indicate the Immobilizer is in the valet/override mode.
4. EXITING THE VALET/OVERRIDE MODE – Insert a valid Touchkey
into the receptacle. EXIT VALET/OVERRIDE MODE AS SOON
AS POSSIBLE TO PREVENT THEFT OF YOUR VEHICLE.
1. If power is ever removed from the Immobilizer and then restored, it
will return to the state prior to removing power (If armed when
power was removed, it returns armed. If disarmed when power is
removed, it remains disarmed.)
2. While driving (when the ignition switch is ON), if the main power is
cut to the Immobilizer, the car will continue to function normally.
1. NUMBER OF TOUCHKEYS – The Immobilizer comes factory
coded to the two Touchkeys included in the package. The unit can
learn the codes of up to 4 Touchkeys.
Note – This procedure deletes the existing Touchkey Codes.
Therefore, you must do this procedure for both existing and new
Touchkeys at the same time.
2. CODE LEARNING PROCEDURE
Note: Immobilizer must be armed before you can enter your PIN.
a. Add the digits ―55‖ to the end of your secret 3-digit PIN. (For
example, if the PIN is 503, the 5-digit code learning PIN
is 50355).
b. While the LED is flashing (indicating the Immobilizer is armed),
turn the ignition ON. The LED will turn steady ON.
c. Turn the ignition OFF and count the flashes. After the 5
th
flash, turn the ignition ON. The LED will be steady ON again.
(This is your PIN’s first digit—5.)
d. Turn the ignition OFF and count the flashes. After the 10th
flash, turn the ignition ON. The LED will be steady ON again.
Note: “0”=10 flashes (2nd digit, 0)
e. Turn the ignition OFF and count the flashes. After the 3rd
flash, turn the ignition ON. The LED will flash rapidly.
(3rd digit, 3)
f. Turn the ignition OFF and count the flashes. After the 5th
flash, turn the ignition ON. The LED will be OFF. (4th digit, 5)
g. Turn the ignition OFF and count the flashes. After the 5th
flash, turn the ignition ON. The LED will flash rapidly.
(5th digit, 5)
h. Leave the ignition key ON. Once the LED stops flashing,
insert a Touchkey into the receptacle within 10 seconds. The
LED will turn steady ON to show the Touchkey was
successfully learned. (Repeat for all touch keys.)
3. EXIT THE CODE LEARNING PROCEDURE – There are three
ways to do this:
a. Turn the ignition switch OFF.
b. Wait more than 10 seconds to insert a new Touchkey.
c. If memory is full (you try to learn a 5th Touchkey), the unit will
go into valet/override mode.
Note: If new codes are programmed, all of the existing Touchkeys
must also be re-programmed.
4. MISTAKES – If the PIN is incorrectly keyed in, simply start over
from the first digit. Ignore any digits that have already been
keyed in.
CODE LEARNING NEW TOUCHKEYS
VALET MODE and EMERGENCY DISARM
POWER DOWN AND POWER UP
TOUCHKEY IMMOBILIZER SLI
®
762FP-ISS
WARRANTY: This SECO-LARM product is warranted against defects in material and workmanship while used in normal service for a period of one (1) year from the date of sale to the original
consumer customer. SECO-LARM’s obligation is limited to the repair or replacement of any defective part if the unit is returned, transportation prepaid, to SECO-LARM.
This Warranty is void if damage is caused by or attributed to acts of God, physical or electrical misuse or abuse, neglect, repair, or alteration, improper or abnormal usage, or faulty installation, or if
for any other reason SECO-LARM determines that such equipment is not operating properly as a result of causes other than defects in material and workmanship.
The sole obligation of SECO-LARM, and the purchaser’s exclusive remedy, shall be limited to replacement or repair only, at SECO-LARM’s option. In no event shall SECO-LARM be liable for any
special, collateral, incidental, or consequential personal or property damages of any kind to the purchaser or anyone else.
NOTICE: The information and specifications printed in this manual are current at the time of publication. However, the SECO-LARM policy is one of continual development and improvement. For
this reason, SECO-LARM reserves the right to change specifications without notice. SECO-LARM is also not responsible for misprints or typographical errors.
Copyright © 2009 SECO-LARM U.S.A., Inc. All rights reserved. This material may not be reproduced or copied, in whole or in part, without the written permission of SECO-LARM.
PITTW3