Filter
Top Products
7
IDENTIFICATION OF PARTS
1
4. Exhaust filter cover
15. AIRBELT shock absorber
16. Carrying handle
17. Suction opening
18. Hose release button (K3 only)
1
9. Hose neck
20. Crevice nozzle
21. Parking attachment holder
22. Power cable shroud
23. AIRBELT clip
24. Parking attachment holder
25. Filter bag cover release catch
26. Filter bag cover
Push the neck (19) of the hose (13) into the suction opening of the canister (17). K3: The notch in the
suction opening will line up with the raised bar on the neck. When the notches are lined up correct-
ly, the neck will snap firmly into place. To release the hose from the suction opening, press the
release tab (18) on the neck of the hose (19), and pull the neck out. K2: To release the hose from
the suction opening, squeeze the tabs (37) on the retaining ring and pull the neck out.
Attach the short mains cable (12 - K3 only) on the underside of the handle by connecting one
cable plug where the hose connects to the handle and the other where the handle connects to
the telescopic tube.
Connect the handle (1) to the top of the telescopic tube (4). Snap in place. To release the telescop-
ic tube (4) from the handle, push the handle release button (3) and slide the handle out.
Attach the head or brush to the bottom of the telescopic tube (4). Insert the bottom of the telescopic
tube into the neck of the head or brush (38) until it locks into place; or line up the square hole in the
telescopic tube with the notches in the front of the neck, and snap firmly into place. To release a head
or brush from the telescopic tube (4), push the release button (7), and pull the head or brush tool off
the end of the telescopic tool. The release button (7) is in the same position on all of the heads, brush-
es and power heads.
To attach the dusting brush clip (27), locate the two raised ridges on the upper end of the telescopic
tube (4) just below the handle. Push the clip onto the tube directly below the ridges then slide the clip
up until it locks onto the ridges. Snap the dusting brush (28) into the holder.
NOTE: To attach a SEBO power head (ET-H, ET-1 or ET-2) to your K3 canister, please refer to your
power head owner’s manual for instructions. Attaching incorrectly could cause damage.
Brushes, Heads, Optional Attachments
29. Premium Parquet nozzle - standard for the
K3 Volcano, Red and Onyx. Optional for the
K2 Midnight Blue - Part #7200DG
30. Combination nozzle - standard for the
K2 Midnight Blue. Optional for the K3
Volcano, Red & Onyx and K2 Hunter
Green - Part #7260DG
31. Turbo nozzle - standard for the K2 Hunter
Green. Optional for the K3 Volcano, Red &
Onyx and K2 Midnight Blue Part #6780ER
32. Radiator brush - Part #1496HG
33. Straight tube (20 in.) - Part #1084HG
34. AIRBELT - Available in several colors
and patterns - Part #6047AM/01-08
20. Crevice nozzle
11. Upholstery nozzle
NOTE: All illustrations shown in this manual represent the K3 model except where part numbers and instructions are different for each model.
1
2
3
4
5
6
7
Power Heads - optional for the K3: 35a. ET-1 Power head - Red: Part #9299AM; Orange: Part #9272AM; Onyx: Part #9951AM
35b. ET-2 Power head - Red: Part #9250AM 36. ET-H Power head - Red: Part #9257AM
31
18
30
32
ASSEMBLY
36
35a
1
. Handle grip
2. Power control slider (K3 only)
3. Handle release button
4. Telescopic tube
5. Slide button
6
. Power cable
7. Tool release button
8. Combination nozzle
9. On/Off power control knob
10. Warning light
11. Upholstery Nozzle
12. Mains cable (K3 only)
13. Hose
19
9
10
11
1
3
14
17
16
1
2
15
8
20
21 22
15
23
24
25
26
11
28
20
27
27. Dusting brush clip
28. Dusting brush
19
17
18
19
17
37
1
4
3
4
38
7
29
33
34
K3
K2
Standard Attachments
35b