Filter
Top Products
5
AsseMblIng tHe VACUUM
Attaching the Handle to the Vacuum
NOTE: Do not plug in the vacuum until it is
completely assembled.
The vacuum cleaner and the handle are
packed separately and require assembly.
• Thread the cord through the lower and upper
cord guides on the back of the vacuum bag (Fig. 1).
• Remove the handle bracket by removing the
two screws (Fig. 2).
• Place handle onto the back of the vacuum,
aligning holes with pegs (Fig. 3).
• Place the handle bracket back into position (Fig. 4).
• Secure with two screws removed in Step 2.
• Open the bag compartment to ensure a
vacuum bag is in place.
• Your vacuum is now ready for use.
• If storing the vacuum, wrap the cord clockwise
around the top and bottom cord hooks. Fasten
the plug to the wrapped cord using the channel
on the plug.
Unwinding the Power Cord
• The lower cord hook rotates to allow for
quick access to the power cord. Turn the
lower cord hook upward and you can quickly
drop the power cord to the floor without
unwinding it from the cord hooks.
• When storing the vacuum cleaner, turn the lower
cord hook to the downward position and wind the
power cord around the cord storage hooks.
DESCRIPTION
DRAWING SIZE:D
PART NUMBER
SHEET 1 OF 1
± .02
± .01
°30" COMMON TO BE CONCETRIC TO .002
TACONY CORPORATION CLAIMS PROPRIETARY
RIGHTS IN THE MATERIAL DISCLOSED HERE IN.
THIS DRAWING IS ISSUED FOR ENGINEERING
INFORMATION ONLY. IT MAY NOT BE REPRO-
DUCED, NOR MAY THE INFORMATION HERE IN
BE USED FOR MANUFACTURING PURPOSES
WITHOUT WRITTEN PERMISSION FROM TACONY
CORPORATION.
DESCRIPTION OF CHANGE
REV
PART NUMBER
SHEET
1 OF 1
A
B
C
D
1
2 3 4
5
6
7
8
7
8
DESCRIPTION
DRAWING SIZE:D
PART NUMBER
SHEET 1 OF 1
± .02
± .01
°30" COMMON TO BE CONCETRIC TO .002
TACONY CORPORATION CLAIMS PROPRIETARY
RIGHTS IN THE MATERIAL DISCLOSED HERE IN.
THIS DRAWING IS ISSUED FOR ENGINEERING
INFORMATION ONLY. IT MAY NOT BE REPRO-
DUCED, NOR MAY THE INFORMATION HERE IN
BE USED FOR MANUFACTURING PURPOSES
WITHOUT WRITTEN PERMISSION FROM TACONY
CORPORATION.
DESCRIPTION OF CHANGE
REV
PART NUMBER
SHEET
1 OF 1
A
B
C
D
1
2 3 4
5
6
7
8
7
8
Fig. 2
Fig. 3
Fig. 4
MATERIAL
DRAWN
ISSUED
SCALE
FINISH
DATE
DATE
DO NOT SCALE
UNLESS OTHERWISE SPECIFIED
DESCRIPTION
DRAWING SIZE:D
PART NUMBER
SHEET 1 OF 1
X.X ±.02 IN RADII X.X ± .02
X.XX ±.01 IN X,XX ± .01
X.XXX ±.005 IN MACHINE SURFACE
X.XXXX ±.0005 IN BREAK SHARP CORNERS TO .010 MAX
± 0° 30" COMMON TO BE CONCETRIC TO .002
TACONY CORPORATION CLAIMS PROPRIETARY
RIGHTS IN THE MATERIAL DISCLOSED HERE IN.
THIS DRAWING IS ISSUED FOR ENGINEERING
INFORMATION ONLY. IT MAY NOT BE REPRO-
DUCED, NOR MAY THE INFORMATION HERE IN
BE USED FOR MANUFACTURING PURPOSES
WITHOUT WRITTEN PERMISSION FROM TACONY
CORPORATION.
1.000
TACONY CORPORATION
1760 Gilsinn Lane, Fenton, MO 63026
PART NUMBER
DESCRIPTION OF CHANGE
REV
PART NUMBER
SHEET
1 OF 1
A
B
C
D
1
2 3 4
5
6
7
8
A
B
C
D
1
2 3 4
5
6
7
8
Fig. 1
DESCRIPTION
DRAWING SIZE:D
PART NUMBER
SHEET 1 OF 1
± .02
± .01
°30" COMMON TO BE CONCETRIC TO .002
TACONY CORPORATION CLAIMS PROPRIETARY
RIGHTS IN THE MATERIAL DISCLOSED HERE IN.
THIS DRAWING IS ISSUED FOR ENGINEERING
INFORMATION ONLY. IT MAY NOT BE REPRO-
DUCED, NOR MAY THE INFORMATION HERE IN
BE USED FOR MANUFACTURING PURPOSES
WITHOUT WRITTEN PERMISSION FROM TACONY
CORPORATION.
DESCRIPTION OF CHANGE
REV
PART NUMBER
SHEET
1 OF 1
A
B
C
D
1
2
5
6
7
8
7
8