Filter
Top Products
18
Regency U41-3 ULTIMATE Gas Fireplace Insert
Installing Glass
1) Install both center and side glass onto extru-
sions as per diagram.
2) Place glass assembly into door frame.
3) Install retainers by placing 1 drop of glue
where previously glued and put in place.
4) Install side retainers.
5) Install door catch plate.
6) Install the 24 nuts loosely, do not tighten
yet.
7) Tighten side panels nuts using the following
procedure:
a. tighten top &
bottom outside
corner nuts (2)
b. tighten inside
nuts (3)
c. tighten top &
bottom inside
corners (2)
GLASS
REPLACEMENT
Your Regency stove is supplied with high tem-
perature, 5 mm Neoceram ceramic glass that
will withstand the highest heat that your unit will
produce. In the event that you break your glass
by impact, purchase your replacement from an
authorized Regency dealer only, and follow our
step-by-step instructions for replacement.
LOG REPLACEMENT
The unit should never be used with broken logs.
Turn off the gas valve and allow the unit to cool
before opening door to carefully remove the
logs. The pilot light generates enough heat to
burn someone. If for any reason a log should
need replacement, you must use the proper
replacement log. The position of these logs
must be as shown in the diagram under Log
Installation.
NOTE: Improper positioning of logs may
create carbon build-up and will alter
the unit’s performance which is not
covered under warranty.
GOLD-PLATED DOORS
The 24 carat gold plated fi nish on the door
requires little maintenance, and need only
be cleaned with a damp cloth. DO NOT use
abrasive materials or chemical cleaners, as
they may harm the fi nish and void the war-
ranty. Clean any fi ngerprints off before turning
the unit on. If gasket seal is not tight - door
may discolour.
DOOR GASKET AND
GLASS GASKET
If the door gasket requires replacement use 7/8"
diameter oval door gasket (Part # 650-920). The
glass requires 5/8" fl at glass gasket (Part # 936-
243). See your Regency Dealer.
LATCH ADJUSTMENT
The door latch may require adjustment as the
door gasket material compresses after a few fi res
and after glass replace-
ment. Turn the adjust-
able latch to tighten or
loosen the latch.
8) Tighten the 10 nuts on center glass re-
tainer.
9) Repeat step 7 for other side panel.
10) Replace new gasket by gluing it in place.
11) Install door onto stove and check the
seal.
PANEL DOOR
1) Remove the door from the unit and place
on a soft surface to prevent scratching.
2) Pull out the door gasket.
3) Remove the nuts holding the glass retainers
in place.
4) Remove the glass retainers (sides, top and
bottom) and the door catch plate.
5) Replace the glass. The glass must have
gasketing around it.
6) Reverse the previous steps, replace the
retainers and fasten with the nuts but do
not overtighten, as this can break the glass.
Note: the door catch plate fi ts on top of the
left side retainer.
7) Put gasket glue on the retainers, but do not
put glue on the screws. Replace the door
gasket, the two ends butt tight together on
the bottom edge of the door.
8) Replace door on the stove and check the
seal.
MITRED DOOR
Removing Glass
Note: Wearing gloves will protect your hands
while handling glass.
1) Remove the door from the unit and place on
a soft surface to prevent scratching.
2) Pull out the door gasket.
3) Remove the 24 nuts holding the glass
retainers in place. Do not remove the nuts
underneath the retainers.
4) Remove the door catch plate.
5) Remove glass retainers on sides fi rst (3 each
side) then remove two center retainers.
Note: Center glass retainers are glued to
center glass.
6) Remove glass from extrusions. When remov-
ing center glass, leave white insulation in
place.
MAINTENANCE