Raypak H-0030B Boiler User Manual


 
2
don't try to repair it, call a qualified service technician.
Force or attempted repair may result in a fire or
explosion.
D. Do not use this boiler if any part has been under
water. Immediately call a qualified service technician
to inspect the boiler and to replace any part of the
control system and any gas control which has been
under water.
FOR STANDING PILOT MODELS WITH ROBERT-
SHAW GAS VALVE, 2 STAGE OPERATION.
(Models 90, 135 & 180)
1. STOP! Read the safety information.
2. Set the thermostat to the lowest setting.
3. Turn off all electric power to the appliance.
4. Push in and move gas control lever counter-
clockwise to "OFF" position.
GAS CONTROL
LEVER SHOWN
IN "OFF" POSITION
GAS INLET
NOTE: Lever cannot be moved from "ON" to "OFF"
unless lever is pushed in slightly. Do not force.
5. Wait five (5) minutes to clear out any gas. Then
smell for gas, including near the floor. If you smell
gas, STOP! Follow "B" in the safety information
above on this label. If your don't smell gas, go to
the next step.
6. Locate pilot mounted on the right side of the burner
drawer, and right of first burner.
THERMOCOUPLE THERMOCOUPLE
ROBERTSHAW PILOT HONEYWELL PILOT
Fig. #8084.1 Fit. # 8083.0
7. Move control lever clockwise to "SET"
position and immediately light pilot with a match.
8. Hold lever in "SET" position for 1/2 minute after
pilot is lit. Release lever, and it will spring back to
"PILOT" position Pilot should remain lit. If it goes
out, repeat steps 4 through 8.
*If lever does not spring back to "PILOT" position
when released, stop and immediately call your
Fig. #8934.0
service technician or gas supplier.
*If the pilot does not stay lit after several tries, move
the gas control lever to "OFF" and call your service
technician or gas supplier.
9. Stand to the side of the heater and move the gas
control lever counterclockwise to "ON".
10. Turn on all electric power to the appliance.
11. Set the thermostat to the desired setting.
TO TURN OFF GAS TO THE BOILER
1. Set the thermostat to the lowest setting.
2. Turn off all electric power to the appliance.
3. Push in and move gas control lever counter-
clockwise to "OFF" position. Do not
force.
LIGHTING INSTRUCTIONS FOR
AUTOMATIC IGNITION MODELS.
Please read carefully and understand the following
safety information before operating the boiler.
WARNING: If you do not follow these instructions
exactly, a fire or explosion may result causing prop-
erty damage, personal injury or loss of life.
A. This boiler does not have a pilot. It is equipped with
a hot surface ignition device which automatically lights
the burners. Do not try to light the burners by hand.
B. BEFORE OPERATING smell all around the boiler
area for gas. Be sure to smell next to the floor because
some gases are heavier than air and will settle on the
floor.
WHAT TO DO IF YOU SMELL GAS
* Do not try to light any appliance.
* Do not touch any electric switch;
* Do not use any phone in your building.
* Immediately call your gas supplier from a
neighbor's phone. Follow the gas
supplier's instructions.
* If you cannot reach your gas supplier, call
the fire department.
C. Use only your hand to push in, move or turn the gas
control knob or lever. Never use tools. If the knob or
lever will not push in, move or turn by hand, don't try to
repair it, call a qualified service technician. Force or
attempted repair may result in a fire or explosion.
D. Do not use this boiler if any part has been under
water. Immediately call a qualified service technician
to inspect the boiler and to replace any part of the
control system and any gas control which has been
underwater.