Filter
Top Products
169
Standard specifications:
MEDIA ROLLS
1. Roll lengths are +/- 5% and widths are -0/+1/2".
2. Maximum roll widths are:
SA600-G10 90.55"
SAR-1 90.55"
All other polyester medias 110"
Fiberglass media 84"
3. Roll Lengths are:
SA600-G10 792"
SAR-1 100 ft.
FP3 50 ft.
1GT 90 ft.
PS125 90 ft.
All other polyester media 100ft.
Fiberglass media 300 ft.
4. Any width can be custom cut from 6" to maximum width
for any media product.
5. Rolls are bagged in minimum 3-mil clear plastic bags.
6. Rolls are identified with a tag on top of each bag.
7. Rolls are individually packaged on LTL orders.
8. All rolls are knife cut without the use of hot wires.
MEDIA PADS
1. Pad dimensions are -1/4"/+1/2" in each direction.
2. SA600-G10 and SAR-1 pads are bagged and boxed.
Full perimeter of box is also taped.
3. All other pads are boxed only.
4. Fiberglass pads are available in vacuum-packed form.
25 pads per bag and 4 bags in each box for 100 filters per
case.
5. SA600-G10 pads are folded exit side to exit side and
rolled to prevent contamination from collecting on the exit
side of the media.
6. All rolls are knife cut without the use of hot wires.
MEDIA
Each media has its own specifications for weight per
square foot, loft, chemical resin weights, tackfier weights,
MSDS sheets, etc. These documents may be obtained by
contacting our corporate office.
Media Varieties:
SA600-G10
Each SA600 media pad and roll has its own model numer.
No custom sizes are used for this media type.
Model Number
EX. SA600-361 or SA600-1001
The first 5 digits identify the SA600-G10 media. If there
are three digits after the hyphen then it is a pad. If there
are four digits after the hyphen, then it is a roll. Model
Number descriptions must be looked up to identify the cor-
rect size, and each model number has a specific case
quantity.
SAR-1
Each SAR-1 media roll and pad also have their own model
number.No custom sizes are used for this media type.
Model Number
EX. SAR1M-24120 or SAR1R-55
The first 4 digits identify the SAR-1 media. If the fifth digit
is an M, then its a media pad, if its an R, then its a media
roll. For the pads, the first two digits after the hyphen iden-
tify the pad width in inches, and the remaining digits iden-
tify the pad length in inches. For the rolls, the remaining
digits identify the roll width in inches.
1GT
1GT media is available in rolls, pads and custom pads. All
model numbers start with 1GT. The fourth digit is R for roll,
P for pad, and C for custom. After the hyphen, the digits
for rolls equal the roll length, the pad size is only listed in
the description, and the digits following the hyphen for
custom pads signify the total square inches for the custom
pad.
330G,331Y,332
Fiberglass media are available in rolls, pads, custom
pads, and vacuum packed pads. For the 330G and 331Y,
the first two digits after the hyphen identify the roll length
and if the last digit is a 0,1,or 2 then the length equals 200
ft. and if it equals 3 then its 300 ft. The 332 uses a "-300"
for all 330 ft. rolls. The pads sizes are listed after the
hyphen and if there is a 0 as the first digit after the hyphen
then the last two digits are the pad width. If there is a V as
the fourth digit, then the pads are vacuum packed.
FP3
If there are only two digits after the hyphen, then its a roll
and the width equals the two digits. If there are four digits
after the hyphen, then its a pad and the dimensions are
listed. Custom pad square inches are also listed after the
Manufacturing
Specifications
For for Media Rolls & Blankets