Filter
Top Products
CAUTION:
This heater includes a Thermal Cut
-
Off Overheat Protection System that shuts the
heater off if it overheats due to abnormal conditions. If this occurs, turn the heater ”OFF”, unplug
it, and inspect and remove any objects on or adjacent to the heater. Allow it to cool for a few
minutes, plug it back in, and resume normal operation.
ADDITIONAL FEATURES
This heater has additional features:
Internal Safety Fuse - acts as back up protection to the Thermal Cut-Off Protection System.
Convenient Carry Handle – allows for easy transport from room to room.
TROUBLESHOOTING
If your heater fails to operate, please follow these instructions:
Ensure that your circuit breaker or fuse is working properly.
Be sure the heater is plugged in and that the electrical outlet is working properly.
Check for any obstruction. If you find any obstruction, turn the heater “ OFF” . Unplug the
heater and wait a few minutes for it to cool down. Carefully remove the obstruction. Plug
the heater in and turn it on again by referring to the OPERATING INSTRUCTIONS.
NOTE: IF YOU EXPERIENCE A PROBLEM WITH YOUR HEATER, PLEASE SEE THE
WARRANTY INFORMATION FOR INSTRUCTIONS. PLEASE DO NOT ATTEMPT TO OPEN OR
REPAIR THE HEATER YOURSELF. DOING SO MAY VOID THE WARRANTY AND COULD
CAUSE DAMAGE OR PERSONAL INJURY. IF THE PROBLEM STILL PERSISTS, PLEASE
CONTACT US BY REFERRING TO THE SERVICE & SUPPORT INFORMATION ON THE
FOLLOWING PAGE.
CLEANING AND STORAGE
It is recommended that the heater be cleaned at least one time during the operating season in order to
provide the optimum level of performance. ALWAYS TURN THE POWER SWITCH OFF AND
UNPLUG THE HEATER BEFORE CLEANING. Be sure to save the box for off-season storage.
Turn the heater “ OFF” , unplug it and wait for the heater to cool down.
Use a dry cloth to clean only external surfaces of the heater.
Do not use any cleaning agents or detergents.
Never immerse the heater in water.
Pack the heater in the original carton and store it in a cool and dry place.
SPECIFICATIONS
Model No.: HF-0023
Voltage: 120V, 60Hz
Current: Maximum continuous draw: 12.5 Amps.
Output: 5200 BTUs
Power: LOW = 900 Watts, HIGH = 1500 Watts; LOW&OSC = 900 Watts,
HIGH&OSC = 1500 Watts
To
lerances on all specifications: Approximately +5%,
-
10%.
OPERATING INSTRUCTIONS
Place the heater on a firm level surface free from obstructions, and at least 3 ft. away
from any wall and any other objects such as furniture, curtains, plants or combustible
material.
With the Power and Setting Control “ A” in the ” OFF” position, plug the heater into a
grounded 120V outlet.
Turn the heater ” ON” by turning the Power and Setting Control “A” clockwise to your
desired power setting ( LOW, HIGH , LOW& OSC or HIGH & OSC). The Power
Indicator Light “ B” will illuminate. The power settings operate as follows:
LOW: The Fan and heating elements operate at 900 Watts.
HIGH: The Fan and heating elements operate at 1500 Watts.
LOW&OSC: The Fan and heating elements operate at 900 Watts.
HIGH&OSC: The Fan and heating elements operate at 1500 Watts.
Turn the Thermostat Control “D” to your desired setting from “ MIN” to “ MAX”. Turning
the thermostat clockwise will increase the “set” temperature; turning the thermostat
counterclockwise will decrease the “set” temperature.
B
C
Carry
Handle
IMPORTANT!
Your heater is equipped with a
polarized alternating current line plug
(a plug having one blade wider than
the other). This plug will fit into the
power outlet only one way. This is a
safety feature. If you are unable to
insert the plug fully into the outlet, try
reversing the plug. If the plug should
still fail to fit, contact your electrician to
replace your outlet. DO NOT defeat
the safety purpose of the polarized
plug.
Control Panel Functions
Power and Setting Control Power Indicator Light
Thermostat Control
A
B
C
A