Filter
Top Products
2 Pelco Manual C489M-A (1/96)
2.0 SCOPE
The information contained within this manual covers
the HS5000/HS5001 High Security/Harsh Environment
Camera Enclosure.
Installation should be in accordance with all applicable
local and national electric codes, utilizing approved
materials only.
3.0 DESCRIPTION
The HS5000/HS5001 is a high security/harsh environ-
ment camera enclosure designed for installations such
as automated mining/excavation equipment, prisons,
detention cells, etc., requiring maximum protection
from vandalism.
Constructed from plate aluminum, the enclosure will
accept two (2) 2-piece cameras with fixed focal length
lenses. An impact resistant, .50" (12.7 mm) thick Lexan
window with Margard is supplied with the enclosure.
The unique “floating” camera sled is shielded from both
vibration and electricity from the enclosure body.
The HS5000 comes with a factory installed “interval”
wiper/washer unit mounted behind a protective “stone
guard” and is equipped with a 20 watt heater to main-
tain internal temperatures. All HS5000 accessories op-
erate at 12 VDC.
The HS5001 comes from the factory without a wiper/
washer or heater unit installed; however, three optional
heater units which operate at 120, 230 or 24 VAC, re-
spectively, are available for use with the HS5001. Op-
eration at 12 VDC is also possible when the 24 VAC
heater unit is installed.
With heater unit installed:
120/230/24 VAC heater -----------40 watts
12VDC ------------------------------ 20 watts
(available if used with 24 VAC heater)
HS5001
HS5000
Heater: 20 watts
Wiper: 3 watts
Washer: 30 watts
3.1 POWER REQUIREMENTS
Model Number Input Voltage Power Consumption Cable Size Cable Distance
EHWD10087 120 VAC 40 watts 20 Awg 1,773 ft (540.4 m)
at 60Hz 18 Awg 2,821 ft (859.8 m)
16 Awg 4,477 ft (1,364.6 m)
EHHK10087 24 VAC 40 watts 20 Awg 70 ft (21.3 m)
at 60Hz 18 Awg 112 ft (34.1 m)
16 Awg 179 ft (54.5m)
HTR40W230V2X2 230 VAC 40 watts 20 Awg 6,514 ft (1.985.5 m)
at 60Hz 18 Awg 10,364 ft (3,158.9 m)
16 Awg 16,449 ft (5,013.7 m)
3.2 RECOMMENDED CABLE SIZE
HS5000
The following cable sizes are the minimum recom-
mended for use with this enclosure (wiper/washer/
heater).
12 VDC at 53 watts
22 Awg 8 ft (2.43 m)
20 Awg 13 ft (3.96 m)
18 Awg 21 ft (6.40 m)
16 Awg 34 ft (10.36 m)
HS5001
The following cable sizes are the minimum
recommended for use with the HS5001 when used with
the 24 VAC heater unit installed operating at 12 VDC.
12 VDC at 20 watts
Cable requirements for HS5001 VAC operation are
listed in the table below–camera power considerations
not included because of the many variations possible.
22 Awg 20 ft (6 m)
20 Awg 30 ft (9.14 m)
18 Awg 50 ft (15.24 m)
16 Awg 80 ft (24.38 m)