Panasonic cz-rd516c Garage Door Opener User Manual


  Open as PDF
of 4
 
3
OPERATION DETAILS
OPERATION DETAILS
The timer setting will shown at wired remote control
only but not at indoor unit’s TIMER indicator.
Check Current Timer Program
Perform the step below to check the timer program for
a particular day.
1. Press Timer
MODE
to enter timer mode.
2. Press
SELECT
to enter day setting.
3. Press Timer
UP
or
DOWN
until your desired day is
shown, press
SELECT
to confi rm your selection.
4. Press Timer
UP
or
DOWN
to check the set programs.
Modify Current Timer Program or Add New Timer
Program
1. Press Timer
MODE
to enter timer mode.
2. Press
SELECT
to enter day setting.
3. Press Timer
UP
or
DOWN
until your desired day is
shown.
4. Perform steps 4 to 7 of “WEEKLY TIMER SETTING”
to modify existing timer program, or add any timer
program.
Cancel Current Timer Program
Perform the step below to cancel the timer program for
a particular day.
1. Press
SELECT
to enter day.
2. Press Timer
UP
or
DOWN
until your desired day is
shown.
3. Press
SELECT
to enter program setting.
4. Press Timer
UP
or
DOWN
until your desired program is
shown.
Press
CANCEL
to cancel the program, will
disappear.
Disable & Enable Weekly Timer
• To disable weekly timer setting, press
MODE
, then
press
CANCE
L
.
• To enable previous weekly timer setting, press
MODE
,
then press
SET
.
DAILY TIMER SETTING
DAILY TIMER SETTING
• To turn ON or OFF the unit at a preset time.
TIMER/CLOCK
MODE
OFF/ON
CANCELCLOCK
SET
SELECTUP
DOWN
1
• Press once to change the
display from Clock to Timer
or vice-versa.
• Press for more than 4
seconds to change the
display from Daily Timer to
Weekly Timer or vice-versa.
3
Set the time
4
Confi rm
2
Select ON or
OFF timer
• To cancel ON or OFF timer, press
CANCEL
.
• Timer operation is based on the clock set in the
remote control and repeats daily once set.
• The timer closest to the current time will be activated
fi rst.
• If timer is cancelled manually or due to power failure,
you can restore the previous setting by pressing
SET
.
WEEKLY TIMER SETTING
WEEKLY TIMER SETTING
• Daily timer and weekly timer could not be set at the
same time.
• Promotes energy saving by allowing you to set up to
6 programs in any given day.
1. Press Timer
MODE
for 4 seconds to change display to
weekly timer.
2. Press Timer
UP
or
DOWN
to select your desired day.
3. Press
SELECT
to confi rm your selection.
4. “1” will be blinking, press
SELECT
to set program 1.
5. Press Timer
OFF/ON
to select ON or OFF timer.
6. Press Timer
UP
or
DOWN
to select your desired time.
If you want to set the timer together with your desired
temperature, press
TEMP
to select the temperature.
7. Press
SET
to confi rm program 1. The selected day will
be highlighted with .
• After 2 seconds, the display will move to the next
program. Repeat steps 4 to 7 to set programs 2 to 6.
• Same timer program cannot be set in the same day.
• During timer setup, if no button is pressed within 30
seconds, or if the
SET
button is pressed, the setting at
that moment is confi rmed and timer setup is ended.
NOTE
NOTE
• POWERFUL, QUIET operation setting could be
operate according to wireless remote control.
• When wired remote control is in operation, the timer
setting from wireless remote control will be cancelled.
F568357-SS1011-0_EN.indd 3F568357-SS1011-0_EN.indd 3 10/17/2011 12:42:01 PM10/17/2011 12:42:01 PM
PANTONE 293 CPANTONE 293 C
 previous